Newman's Speed Shop

Newman's Speed Shop Repairs and Performance modifications on vintage and late models vehicles.

Just finished up this LS swap on an S-10 for a customer. This rig is going to be rowdy when it hits the street. It's run...
02/16/2025

Just finished up this LS swap on an S-10 for a customer. This rig is going to be rowdy when it hits the street. It's running an MSD 6014 unit for ignition and a Brawler 750 carb for fuel. All the wires were cleaned up and loomed for a nice and neat install.

New motor mounts are installed. New motor is hopefully sitting in its home for good. Really nice and simple belt setup o...
12/31/2024

New motor mounts are installed. New motor is hopefully sitting in its home for good. Really nice and simple belt setup on this 5.3. Going for a carbureted setup on this one.

Out with the old. Making room for new goodness. It’s gonna be good! Lots of work still left to do.
12/19/2024

Out with the old. Making room for new goodness. It’s gonna be good! Lots of work still left to do.

Pretty clean truck. The old motor and trans will be out soon. Got to make way for new shiny goodness!!
12/14/2024

Pretty clean truck. The old motor and trans will be out soon. Got to make way for new shiny goodness!!

New project incoming!! This is gonna be a good one!!
12/07/2024

New project incoming!! This is gonna be a good one!!

The 64 is sporting a fresh 350. A lot of work has been done to this beautiful old truck. Besides the new motor I have re...
06/15/2024

The 64 is sporting a fresh 350. A lot of work has been done to this beautiful old truck. Besides the new motor I have replaced some wiring, added a new ignition switch, installed an oil pressure gauge and an electric fuel pump was installed with a relay kit to power it.

Got a good start on the 64 last night. Engine is out. Now to prep for reinstall and other goodies. This old 283 has a co...
05/30/2024

Got a good start on the 64 last night. Engine is out. Now to prep for reinstall and other goodies. This old 283 has a cool refurbish tag from 1967. Lists the bore and bearings in the engine when built.

Sneak peek on the next job in the shop. 1964 C10 is getting a fresh 350 in place of the wore out 283. Plans to tie up lo...
05/05/2024

Sneak peek on the next job in the shop. 1964 C10 is getting a fresh 350 in place of the wore out 283. Plans to tie up loose ends and refresh a few things to make it reliable. Stay tuned.

Had a Silverado in the shop for some A/C work. Installed a new compressor, or***ce tube, drier, condenser and a belt ten...
05/01/2024

Had a Silverado in the shop for some A/C work. Installed a new compressor, or***ce tube, drier, condenser and a belt tensioner. The system was vacuumed down and recharged and is now cold as ice. A/C stop leak does not solve problems. It only patches and creates more. If anyone is in need of some work please feel free to contact me through Facebook or call/text 6014106713.

The Bel Air is out of the shop. Head gasket repaired with Felpro gaskets. Cleaned up a bit under the hood. Installed the...
04/22/2024

The Bel Air is out of the shop. Head gasket repaired with Felpro gaskets. Cleaned up a bit under the hood. Installed the new MSD billet distributor and coil. Customer already planning for more work going forward.

1965 Chevy Bel Air in the shop for a bit of work. Head gasket repair, new heads and new MSD distributor are in store. Ti...
04/13/2024

1965 Chevy Bel Air in the shop for a bit of work. Head gasket repair, new heads and new MSD distributor are in store. Time to get this beauty back on the road where it belongs.

Address

Waynesboro, MS
39367

Telephone

+16014106713

Website

Alerts

Be the first to know and let us send you an email when Newman's Speed Shop posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Newman's Speed Shop:

Shortcuts

Share

Category