Dan Neumann Race Cars LLC

Directions Website Contact the business

Dan Neumann Race Cars LLC Proud to say I'm still producing quality builds 24 years later.

I opened DNRC back in Oct. 2002 to fulfill a need I seen in the Florida drag racing scene and that was a chassis shop that catered to more of the weekend warrior door slammer drag racer.

Not too terribly shabby for only machine built-in pulse that I'm a newbie at.
10/20/2026

Not too terribly shabby for only machine built-in pulse that I'm a newbie at.

My little jig.
10/20/2026

My little jig.

3D printing a jig to help with mounting the wastegates perfectly equal on each side of the Mustang. Michael Heath Preci...
10/19/2026

3D printing a jig to help with mounting the wastegates perfectly equal on each side of the Mustang. Michael Heath Precision Turbo & Engine Kenny Parramore

10/17/2026

Anyone who truly knows me knows I don't pull any punches and I don't lie about FACTS. If I purchase something and over time that items turns out to be trash I'm going to let the world know my true world experience with said item. Just putting that out there.

Send a message to learn more

I miss this old legend. Who knows who this great guy was?
10/15/2026

I miss this old legend. Who knows who this great guy was?

So because this Holley EFI harness has a Power Tap installed in it and I wanted to be able to connect the Holley alterna...
10/15/2026

So because this Holley EFI harness has a Power Tap installed in it and I wanted to be able to connect the Holley alternator and some additional pressure sensors like dome pressure, converter charge pressure, etc to it without having to do a bunch of splicing. I installed a terminal strip with jumpers so it will be easy to add those items or remove them if I wish with ease. It's mounted under the dash within' inches of the ECU and is easy to access. When it's all done it has a plastic cover that goes over it for protection.

Decided to 3D print a larger button but also in red. Made from ASA filament to handle the UV rays and heat.
10/15/2026

Decided to 3D print a larger button but also in red. Made from ASA filament to handle the UV rays and heat.

One reason I love living in Florida. I walked outside to see this 15 minutes ago. A SpaceX rocket launch.
10/13/2026

One reason I love living in Florida. I walked outside to see this 15 minutes ago. A SpaceX rocket launch.

I decided I needed to add a 'switched 12v' terminal strip for all the components needing one so I CAD drew up a terminal...
10/12/2026

I decided I needed to add a 'switched 12v' terminal strip for all the components needing one so I CAD drew up a terminal jumper bar and cut one on my CNC plasma table out of .060" copper sheet I had. And not pictured I put a little red liquid electrical tape on the edge of it just to prevent any whoopsies.

I needed another wire pass-thru in the firewall of the Malibu for a few more wires like WG boost pressure sensor, boost ...
10/12/2026

I needed another wire pass-thru in the firewall of the Malibu for a few more wires like WG boost pressure sensor, boost controller solenoids, fans and an alternator wire. I hate using those cheap ass rubber grommets whenever possible so I whipped up one of my own similar to the 'Seals-It' style grommets that the sleeved wires can pass thru.

Address

3690 NE 45TH Place
Ocala, FL
34479

Opening Hours

Monday 8am - 5pm
Tuesday 8am - 5pm
Wednesday 8am - 5pm
Thursday 8am - 5pm
Friday 8am - 5pm

Website

Alerts

Be the first to know and let us send you an email when Dan Neumann Race Cars LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Dan Neumann Race Cars LLC:

Shortcuts

Share

Category