J.C.D Repair Shop

J.C.D Repair Shop Complete service and repair shop for all your needs in anything powersports or small engines. Contact us through here or at
[email protected]

Toro zero turn mower came in the shop with an electrical mess. The ignition switch was once replaced with a 12v push but...
06/12/2026

Toro zero turn mower came in the shop with an electrical mess.
The ignition switch was once replaced with a 12v push button switch but was wired incorrectly and melted the harness abit. (Had one single 16ga wire powering everything and charging wire was ran backfeeding through ignition switch)

All this mess was removed and rewired back with a factory ignition switch with single charge wire feeding to positive post of starter solenoid.

Finished this one off with a blade sharpening and put it to the test!

Good to go!

Timecutter 5000 mower arrived with a black smoke bogging issue and an engine that wouldn't rev up fully, many would susp...
06/12/2026

Timecutter 5000 mower arrived with a black smoke bogging issue and an engine that wouldn't rev up fully, many would suspect carburetor issues.
However, the actual cause was the pulse fuel pump's compromised rubber diaphragm, which had developed an internal crack. This allowed excessive fuel to be drawn into the intake port, resulting in an overly rich running engine.

Super simple and cheap repair.

Got this 125cc kids quad all fixed up after being recently bought. This machine wouldn't idle, valves were noisy and ove...
06/03/2026

Got this 125cc kids quad all fixed up after being recently bought.

This machine wouldn't idle, valves were noisy and overall ran rough.

•New battery
•Cleaned/jetted the factory carb
•Adjusted the valves
•Lubricated the front brake mechanical linkage
•Oil change
• Air filter
•Greased ball joints
• Adjusted/lubricated drive chain
•Set tire pressure
• Fixed horn
•New inline gas filter

Finally a good wash and it's back to the owner the following day.

Need work call J.C.D Repair Shop
814-496-2930

2023 crb 1000 came in the shop for a new rear tire. 🏍Such a beautiful bike
05/30/2026

2023 crb 1000 came in the shop for a new rear tire. 🏍

Such a beautiful bike

2018 canam outlander 570 came in the shop for a new set of tires.Found a nice new set of Wanda tires for it and finished...
05/22/2026

2018 canam outlander 570 came in the shop for a new set of tires.
Found a nice new set of Wanda tires for it and finished this machine off with an oil/filter change.

On to the next machine!

2022 kawasaki zx6r came in for a service. Battery was stone dead and needed a replacement after sitting this past winter...
05/22/2026

2022 kawasaki zx6r came in for a service.
Battery was stone dead and needed a replacement after sitting this past winter. Gave the machine a oil change and it's ready to go for the season!

Need any work, call 814-496-2930

This beautiful 2024 krx 1000 came in for tire rotation and a quick look over. Fixed 2 leaking tires and adjusted the e-b...
05/20/2026

This beautiful 2024 krx 1000 came in for tire rotation and a quick look over.

Fixed 2 leaking tires and adjusted the e-brake, it's back in the owner after just a few hours

2009 Yamaha rhino 700 came in the shop for a handful of issues. Starting out, the coolant temp sensor was malfunctioning...
05/12/2026

2009 Yamaha rhino 700 came in the shop for a handful of issues.

Starting out, the coolant temp sensor was malfunctioning and causing the machine to overheat.

The second issue was in relation to the stator and charging system failed and the machine would only run on battery power until the machine went to 9v and into limp mode.
Got it apart and the stator was fried, the internal windings had shorted out to ground from age and added accessories.

New stator
New rectifier
New coolant temp sensor

Charging and cooling system both successfully repaired.
Back in the woods it goes!

Had this huski 480xl come in the shop after sitting this past winter. After having a quick look around, I noticed the fu...
05/12/2026

Had this huski 480xl come in the shop after sitting this past winter.

After having a quick look around, I noticed the fuel system was contaminated with tons of water and the vacuum fuel pump was disintegrating in my hands as I removed the fuel lines.

Cleaned carb
Air filter
Drained fuel tank
New fuel pump
New gas
Checked oil
New inline fuel filter

Finish it off with sharpening the blades on this unit and it's back to mowing.

All 4 new tires for this 2013 arctic cat 300. Love the quick and easy jobs!
05/05/2026

All 4 new tires for this 2013 arctic cat 300.

Love the quick and easy jobs!

Address

Madera, PA

Opening Hours

Monday 10am - 7pm
Tuesday 10am - 7pm
Wednesday 10am - 7pm
Thursday 10am - 7pm
Friday 10am - 7pm
Saturday 10am - 7pm

Telephone

+18144962930

Website

Alerts

Be the first to know and let us send you an email when J.C.D Repair Shop posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to J.C.D Repair Shop:

Shortcuts

Share

Category