BakerBuilt Garage

Call Directions Contact the business

BakerBuilt Garage General Maintenance
Diagnostics
Brakes
Suspension
Engine Swaps
& More!

HONDA-ACURA-TOYOTA Specialist
In-House Mainline Dyno
AEM, Haltech, Hondata, Neptune & More EFI Tuning
Engine Swaps
Honda B/K Series Manual Transmission Building
Wire/Brake Tucks
E85 Fuel Systems & Parts
Diagnostics
General Maintenance & Repair

'98 Toyota Chaser in for a rear main crank seal and new Clutch Masters Industries, Inc clutch and flywheel 👏
10/14/2026

'98 Toyota Chaser in for a rear main crank seal and new Clutch Masters Industries, Inc clutch and flywheel 👏

10/14/2026

Dont think we've ever seen a twin disc clutch this low 😳

10/14/2026

Jay Vineyard 's beautiful supra we had in recently. We had to tidy up a few things and do the thing with the buttons on the laptop 💻
us built bottom end. GE VVTI head with 264 cams. turbo manifold holding up Gen 2 6466. All controlled by Nexus S3 ECU. Flex fuel implemented. She put down a cool 700hp 571tq at about 23 psi on pump E85. This combo with the artec manifold spools up at about 2500 rpm 😳

She looks great, sounds great, and checks all the boxes for a nice street setup 🔥

JZX81 Chaser got some upgrades 🔥-Ferrea Racing Components valve stem seals-Automotive Racing Products Inc. head studs -N...
10/09/2026

JZX81 Chaser got some upgrades 🔥

-Ferrea Racing Components valve stem seals
-Automotive Racing Products Inc. head studs
-New timing belt, pulley & tensioner
-2JZ water pump conversion
-New cam & crank seals
-Mishimoto radiator
-Brian Crower | Engine Internals 272 camshafts & valvetrain
-Fluidampr crank damper
-OEM Sequoia alternator
-Yaris coil conversion
-Haltech Elite 2500 ecu with boomslang adapter
-Electric fan conversion with PROFORM Parts brushless fans

It has a CX racing turbo manifold with a Driftmotion 6466 turbo. Stock 1JZ GTE bottom end.

On pump E85 at around 24psi she put down 565hp 452tq

K24 turbo 8th gen civic si 🔥Rich brought us his recently aquired 8th gen SI for a bit of maintenance and tuning. Overall...
10/08/2026

K24 turbo 8th gen civic si 🔥

Rich brought us his recently aquired 8th gen SI for a bit of maintenance and tuning. Overall it was well put together, just needing some odds and ends. Stock K24 with a Deivi Cerritos turbo kit & A/C tuck kit, and Alpha Injection Clinic injectors.

We found a few boost leaks in the intercooler system, and an exhaust leak due to loose turbo manifold hardware. The drivetrain to chassis grounds were not done well, causing some wonky readings. Got that taken care of and it was happier. We also installed an ethanol content sensor to implement flex fuel capabilities.

On pump E85 on about 20 psi she put down 583hp 441tq at 8k rpm. It will be turned down a bit from that on the street as we did not want to push it with stock valvetrain. It will be a very fun car to drive 👏

1996 Toyota T100 maintenance 👏-Timing belt-Water pump-Thermostat -Cam & crank seals-Oil cooler hoses & seal-Cooling syst...
10/08/2026

1996 Toyota T100 maintenance 👏

-Timing belt
-Water pump
-Thermostat
-Cam & crank seals
-Oil cooler hoses & seal
-Cooling system flush
-Radiator hoses
-Transmission mount
-Brake fluid flush

1993 Toyota Land Cruiser got some much deserved attention! It came in with a few leaks and the a/c was not working. The ...
10/08/2026

1993 Toyota Land Cruiser got some much deserved attention! It came in with a few leaks and the a/c was not working. The head gasket was replaced previously, but there were a few items looked over that needed to be done.

-New heater control valve
-New heater/coolant hoses
-New radiator hoses
-New transmission cooler hoses
-New manifold vacuum lines all over
-New fuel evap hoses
-A/C pressure switch replaced & system recharged

287k miles, and plenty more to go 🫡

Composite turbo gaskets will fail you 👎🚮On the dyno, we were fighting some boost issues with this one. It wasn't blown c...
10/06/2026

Composite turbo gaskets will fail you 👎🚮

On the dyno, we were fighting some boost issues with this one. It wasn't blown completely out at first, but got worse as the session progressed. Started peeking around and it made sense. Last time we saw the car we looked at it and said "those will be a problem eventually", and sure enough it became a problem.

We always recommend steel fl**ge gaskets. Same goes for the manifold to cylinder head. Use oem or multi layer steel gaskets if available.

RSX Type-S in for a new clutch, rear main crank seal, ball joints, control arms, and valve lash adjustment.331k miles do...
09/30/2026

RSX Type-S in for a new clutch, rear main crank seal, ball joints, control arms, and valve lash adjustment.
331k miles down, many more to go 👏

Address

10418 New Berlin Road (Unit: 211-212)
Jacksonville, FL
32226

Opening Hours

Monday 9am - 6pm
Tuesday 9am - 6pm
Wednesday 9am - 6pm
Thursday 9am - 6pm
Friday 9am - 6pm

Telephone

+19046773327

Website

Alerts

Be the first to know and let us send you an email when BakerBuilt Garage posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to BakerBuilt Garage:

Shortcuts

Share

Category