RPM Performance

08/31/2026

Dangerous heat temps and indexes are causing us to cancel this event. We will be back next month!

❗️No Cruise-In this week at RPM❗️

See you back here in October for the RPM Performance Cruise-In

08/27/2026

The beautiful 68 convertible Chevelle left today also. As you can see, father and son are extremely happy with the new power steering system, and all the engine and transmission leaks repaired.

08/27/2026

Another happy customer picked up today after a complete engine rebuild and new exhaust system.
The 318 Dodge we bored .030 and replaced with flat top pistons to get 10-1 compression with the stock heads. The crankshaft was turned .010/.010 and bearings plastiguaged for the correct clearance. The heads were completely gone through and refreshened with valve job, guides, seals, and new springs.
She’s running strong, sounding good, and as you can see, Gene is a very happy man!

08/24/2026

1st and 2nd stages done today! With all the growth we have been seeing with new customers lately, It Will be great right now to have the extra parking and storage for our customers vehicles, and also for our big events!

08/24/2026

Man it is a B E A utiful day today! We have all the shop doors open working inside and outside on all these awesome cars and enjoying this beautiful weather.
But wait! What’s going on behind the shop??

08/19/2026

Several projects in the works this month pushing to have completed by next week. Mostly new engine builds, or transmission and rear end rebuilds. Also a lot of maintenance type repairs like radiators, water pumps, or electrical gremlins. This hot summer has really stressed a lot on these muscle cars.

08/13/2026

Check out this rare 86 Buick Regal T type that we did a complete engine rebuild on due to a lower end knock.
We ended up needing to:
Pull the engine, disassemble, and inspect the rotating assembly.
Resurface the cylinder heads, and Perform a complete valve job.
Degrease, hot tank, and clean the block
Cleaned and inspect Pistons
honed the cylinder walls for new rings.
Grind the crank .020/.020 and install with new correct main and rod bearings.
Reconditioned the rods and install pistons
Assemble engine with all new bearings, seals, and gaskets.
After we finished installing the engine with fresh oil, spark plugs, and minor tuning, we took the customer for a ride and his smile said everything!
So glad we could get your baby repaired and make you happy again Alex! We know you will enjoy it!

08/07/2026

Been an amazingly busy year at the shop. This week we finished up the GT40 repairs, and two new complete engine builds.
The 318 Dodge we bored .030 and replaced with flat top pistons to get 10-1 compression with the stock heads. The crankshaft was turned .010/.010 and bearings plastiguaged for the correct clearance. The heads were completely gone through and refreshened with valve job, guides, seals, and new springs.
The 327 Chevy engine was bored .040 with flat top pistons. Whole new rotating assembly, and a new set of aluminum heads that will get this engine real close to 11-1 compression. This will be a high revving, great sounding, HP making engine to propel the little nova deuce it’s going in. Can’t wait to have these cars back on the street, hanging out at with them at some of the same places, and watching them finally happy!

05/12/2026

The Season is kicking off and we are a part of so many events going on. It is really awesome to not only be involved in these events, but watch some of the very cars we work on be a part of it also!
Whether it’s local car shows, cruise in’s, RPM shop events, or drag racing, we are there supporting you as you support us!
Thank you to all of our customers for allowing us to do what we love, so you can do what you love!

05/07/2026

Customer broke the 7.5” stock rear end on this LS swapped big wheel Caprice, so we painted and installed a Moser 9” with a Tru trac 3rd member and 3.73 gears. He won’t break this one!

If you’re looking to upgrade the rear end in your car or truck, give us a call! We do everything from gear changes, to complete replacements.