boricua_motorwork

boricua_motorwork We work on all types of vehicles and do all types of work. tune ups, brakes ,suspension, electrical, engine swap/rebuild and engine performance (no tuning yet)

Dodge GPEC services available now! From programming new modules to cloning onto new or used modules. As well as GPEC unl...
10/17/2025

Dodge GPEC services available now! From programming new modules to cloning onto new or used modules. As well as GPEC unlocking so you are able to tune your ride! Message me to set up appointments.

Another monday!! Customer complaint was the vehicle would not register oil pressure. Also the vehicle would shift hard w...
09/22/2025

Another monday!! Customer complaint was the vehicle would not register oil pressure. Also the vehicle would shift hard when first going into gear. Customer changed oil pressure switch and tested the oil pressure. So I ruled those out.

I scanned the vehicle saw the there was loss of communication with multiple modules. Also there was a code the CAN Bus.
I tested the modules , the grounds and powers and all were good. Then I isolated the wiring harness and found that it was shorted to ground.
1 one of the wires in the can bus was severed and another 2 wires rubbing on the frame.

I fixed the cables , re-insulated , re-assembled and the truck is running a1.

*King of the Powerstrokes*This 2003 Ford F550 with 7.3 powerstroke was brought because it would run really rough sometim...
08/12/2025

*King of the Powerstrokes*
This 2003 Ford F550 with 7.3 powerstroke was brought because it would run really rough sometimes. After some testing, I found out 2 injectors were not contributing as they should. Causing fuel knock. We replaced the injectors , the wiring for the injectors, and now the vehicle is back on the road doing it job. This is by far the most reliable and durable powerstroke ever built. I know the powerstroke guys will agree with me.

Found myself scrolling through my photos. 80% off the photos in my phone are of engines 🤣 90% off those are hemis. I hav...
08/07/2025

Found myself scrolling through my photos. 80% off the photos in my phone are of engines 🤣 90% off those are hemis. I have built easily over a hundred of these engines. I could probably build one with my eyes close. I have built and tried almost every possible combination with these engines.

First generation 6.4 in the shop for some wiring issues in the tailight, suspension work , and kill switch installation.
07/25/2025

First generation 6.4 in the shop for some wiring issues in the tailight, suspension work , and kill switch installation.

Finishing up this beautiful Durango !! Had a couple of issues, but now it's running like new.Issues fixed:Replaced the ...
07/08/2025

Finishing up this beautiful Durango !! Had a couple of issues, but now it's running like new.

Issues fixed:
Replaced the water pump because the pulley had a lot of play in it. Those water pumps are no joke they cost almost $1000 @ the dealer.
Used a 180-degree thermostat in it.
Repalce Ac Hose and coolant hoses to the FI Interchiller. Refilled ac system.
Replaced the old supercharger with a new ported supercharger from .

Modifications:
Kong Ported supercharger
Kong 108 mm throttle body
Fore innovations thriple pump set up
E-85
FI Interchiller
10% lower ATI damper
Griptec 2.60 upper pulley

This hellcat makes close to 1000hp if not more. Its a dig monster 😈

ANOTHER ONE!!!Performing a head gasket job on this Chrysler 300 STR8. I'm staying super busy with all these i have bee...
06/06/2025

ANOTHER ONE!!!

Performing a head gasket job on this Chrysler 300 STR8. I'm staying super busy with all these i have been having in the shop lately.

A couple of things I missed in the video are the head was warped , which was the reason antifreeze was being consumed. T...
04/28/2025

A couple of things I missed in the video are the head was warped , which was the reason antifreeze was being consumed. The piston ring is pinched because whatever cause the damage to the head and top of the piston crushed where the rings sit at. Not allowing the rings to expand fully . Which is letting oil go by and also consuming oil. The timing was completely new. It looks like an off brand. One of the phasers was missing the dot and the pin to make sure it sits properly in the cam. This was the main concern of the customer, but it was not the biggest issue, unfortunately.

The cleanest 07 GT i have ever seen. The customer complaint was that the vehicle would shake and the engine had no pow...
04/24/2025

The cleanest 07 GT i have ever seen.
The customer complaint was that the vehicle would shake and the engine had no power.
After diagnosing the vehicle. I found the timing chain jumped out of time. Replace all the timing components (chains, guides, vvt solenoid, vvt sprockets). Now the car is running like new again.

New injectors for BMW X6 , a common issue for the 3.0 twin turbo engine.
03/13/2025

New injectors for BMW X6 , a common issue for the 3.0 twin turbo engine.

Replacing front differential and both cv shafts on 2012 Ram 1500
02/17/2025

Replacing front differential and both cv shafts on 2012 Ram 1500

Engine replacement on the early Gen3 Hemi Chrysler 300C.
01/27/2025

Engine replacement on the early Gen3 Hemi Chrysler 300C.

Address

Indianapolis, IN
46203

Opening Hours

Monday 9am - 7pm
Tuesday 9am - 7pm
Wednesday 9am - 6pm
Thursday 9am - 7pm
Friday 9am - 6pm
Saturday 9am - 7pm

Website

Alerts

Be the first to know and let us send you an email when boricua_motorwork posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category