Wagner Amp Repair

Wagner Amp Repair BY APPOINTMENT ONLY: Located on the east side of Erie in Harborcreek, specializing in maintenance, repairs & mods of guitar/bass amps (esp.
(1)

tubes), pedals, mixers/PAs. NO CAR AUDIO OR KEYBOARDS

Complaint for this Fender Blues Jr Tweed version was that the amp crackles and pops, the volume drops out, and the high ...
07/20/2026

Complaint for this Fender Blues Jr Tweed version was that the amp crackles and pops, the volume drops out, and the high end drops out, and it is intermittent. The client also asked if something could be done with the master volume to make it more useable/controllable.

The master volume in this is an odd design. Fender chose to use a linear taper pot for the master volume, but we hear logarithmically. I’m puzzled by their design decision on this one. Good thing there is a drop in replacement pot with the correct audio taper available. Got that installed without issue.

Fender is also notorious for running tubes hot in this amp. And it killed one of the power tubes. You can see how discolored the labeling is in the photos. Tubes on the tester show that they were rode hard and ready for retirement. A new pair of matched EL84 tubes were installed. The bias was cooled off a bit to prolong tube life without sacrificing tone. All of the jacks were cleaned and solder joints were inspected and in good condition.

With the new pot, new tubes and cooler bias, the owner is ecstatic. He said the amp sounds phenomenal and he can now play it at home with no headaches anymore as he has much better control over his volume. That’s a win in my book.

It's been a hot minute since the last album was posted. Here’s an intriguing amp that I’ve been wanting to play througho...
06/27/2026

It's been a hot minute since the last album was posted. Here’s an intriguing amp that I’ve been wanting to play throughout the years. Complaint on this Carvin V3MC was that the amp loses volume and randomly switches to odd EQ settings. The reverb stopped working and would then be intermittent. Shipping of the amp’s chassis wasn’t kind as one preamp tube and one power amp tube were broken when it arrived.

There’s a lot packed inside this amp so it’s not for the inexperienced to tackle. It is tricky to disassemble and reassemble. Studying the schematics and the symptoms, I deduced it was an issue with the 5V regulators. The odd EQ settings are because when the regulator failed, it switched to the other channel’s EQ. The 5V regulators were replaced on the main board, plus the reverb board since that board was also readily accessible at this point. All of the boards were cleaned, and the ribbon cable connections were cleaned and reseated. The pots and jacks were also cleaned.

The footswitch reverb pushbutton was not making solid contact when switching, causing the reverb to also sometimes work or not. The pushbutton on the footswitch was replaced. Replacement tubes for the broken ones were installed. Power tubes were biased per Carvin’s spec. Playing the amp to confirm the repair was enjoyable. Got the amp back to the owner and it has been working flawlessly since. Rock on, Bundy!

Do you like small, compact, lightweight, powerful vintage amps? If so, this one’s got your ticket punched. Doing a littl...
04/10/2026

Do you like small, compact, lightweight, powerful vintage amps? If so, this one’s got your ticket punched. Doing a little research on this first generation Walter Woods MI-100 amp, I learned that it was designed to compete with the much larger and heavier Ampeg SVT amps. This certainly lives up to that.

Owner requested a new power switch and power cord, plus cleaning of the controls. To access the power switch does require a fair bit of disassembly, but as long as you’re paying attention, it isn’t difficult to do. I will caution that there’s a hidden toggle switch in the heat sink fins that I didn’t catch initially when removing the rear. More on that later.

Cleaning the pots and jacks was straightforward. The owner asked for a toggle instead of the pushbutton for the power switch. I was able to find a mini toggle that fit in the space and had sufficient ratings for the duty it was to handle. I also swapped out the power cord for a new one. In doing so, I also rewired the fuse to be on the hot side of the incoming power and adjusted the filter module input wiring to accommodate the brown/blue international color scheme for the hot and neutral wires.

Once those were done, the unit was powered on and voltage rails were checked. They were reading about half of what I was expecting. After studying the circuit traces, I flipped that hidden toggle and was able to confirm that the voltages are back to where they should be. Seems that toggle switch was a 120/240 power switch. The amp was reassembled and tested again. Overall, this was a very interesting amp that impressed me with the design, features, sound and package.

Here’s another fun vintage amp where the owner requested a fairly significant conversion. He requested implementing some...
02/28/2026

Here’s another fun vintage amp where the owner requested a fairly significant conversion. He requested implementing something similar to what the guitologist video did. One thing you’ll find on a lot of these old amps is that the amp in front of you doesn’t always match (even closely) the schematic for the amp. That required tracing out the existing circuits to understand what the components were doing.

The amp had some prior work done to it, but wasn’t in great shape. Significant rework was performed. All new electrolytic caps, updated heater wiring, single input jack, add bright switch, change tone stack to Marshall style, add a mid pot, new OT with multi-taps and impedance switch. The original footswitch has the buttons too close so a new footswitch control jack for typical 2 button footswitch was added to rear panel. The reverb transformer was shot so we went with the option to convert both the transformer and the reverb tank (and RCA jacks) to the more common Fender style for less than the replacement transformer for the original. The power switch was replaced; a new purple jewel lamp was installed along with a 3-prong power cord. Add in some new matched EL84 tubes, clean the pots and jacks and she’s now able to sing in many tones. The owner is ecstatic with the transformation.

11/27/2025

Happy Thanksgiving to you and your loved ones!

Here’s another fun amp. The request was to modify the Peavey Windsor to add more gain. While there are a handful of mods...
11/15/2025

Here’s another fun amp. The request was to modify the Peavey Windsor to add more gain. While there are a handful of mods for this amp out there, I wasn’t able to find exactly what I was looking for. So, it was time to get a little creative and combine some ideas from others as well as do a few tweaks myself.

First up was to clean up all of the dust. Then pull the chassis and see if anything needs attention before surgery. As is typical with amps of this generation, you’ll find cracked solder joints around many of the jacks that see high usage. The pots and jacks were cleaned and resoldered to ensure a good connection. All tubes tested strong so no need to change them. For the mods, I either changed or removed a handful of resistors and caps, plus rewired the circuit in a few places and ended up with more gain than the circuit originally had. Overall, it has much more gain than stock while retaining clarity.

This 80s rocker came in with complaints of no sound. Once the chassis was pulled, there were signs of components overhea...
10/26/2025

This 80s rocker came in with complaints of no sound. Once the chassis was pulled, there were signs of components overheating. Luckily the outputs and reverb tank were still good. Issue was that the low voltage power supplies were not functioning. For this amp, it is common to be related to a bad reverb tank, but not in this case. The low voltage supply was rebuilt. The reverb driver transistors were changed out and a balance resistor tying their bases (found on newer versions of this amp) was added. All pots, jacks and contacts were cleaned and it’s back in business.

Another updated list of the various manufacturers of guitar/bass/keyboard amplifiers, plus mixers, PAs, pedals, and othe...
08/30/2025

Another updated list of the various manufacturers of guitar/bass/keyboard amplifiers, plus mixers, PAs, pedals, and other equipment that I've serviced.

This late 80s amp wasn’t producing the full sound range except if the stereo chorus was turned on. From the outside, you...
08/23/2025

This late 80s amp wasn’t producing the full sound range except if the stereo chorus was turned on. From the outside, you could see a few of the jacks were broken. Once inside and the board was pulled, several cracked solder joints were exposed.

The bad jacks were replaced. The gain pot shaft was badly bent so the pot was replaced. Numerous solder joints were reflowed, the board cleaned, new thermal grease applied to the outputs and all pots and jacks were cleaned. But, once that was all working correctly, it still didn’t sound quite right in the cabinet. That’s when it was determined the speakers were miswired out of phase. Correcting that and now the amp sounds like it should.

It’s not everyday that rack mount gear comes thru the shop. The complaint on this particular EQ unit was the sound would...
07/20/2025

It’s not everyday that rack mount gear comes thru the shop. The complaint on this particular EQ unit was the sound would cut out intermittently and it didn’t always work. Tearing into the unit revealed there is not a whole lot to go wrong.

A careful inspection of the board revealed a factory manufacturing process defect. I’m not surprised that this would sometimes work. One of the power supply pins to one of the opamps had no solder at all. The pin would occasionally touch the solder hole enough to power the chip, but definitely not a reliable joint.

Removal of the board requires careful removal of the k***s. You will need a slotted screwdriver to loosen the wedge type connection on them. Once the board was pulled, solder was added to U4 pin 8, and a handful of other solder joints that were either cracked or had insufficient solder were touched up. With those issues taken care of, the unit is working correctly again.

Address

Erie, PA
16510

Opening Hours

Monday 12pm - 6pm
Tuesday 12pm - 6pm
Wednesday 12pm - 6pm
Thursday 12pm - 6pm
Friday 12pm - 6pm

Telephone

+18147462939

Website

Alerts

Be the first to know and let us send you an email when Wagner Amp Repair posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share