Fame Garage

04/20/2026

Coming in clutch!! Badum tssss 🥁

Had this '01 Jeep Wrangler brought in needing a clutch replacement. Got it out to see this.. The customer stated it was done 30k miles ago. I honestly don't think the release bearing was replaced at that time for whatever reason but we got him in and out with a new clutch set, flywheel and clutch slave cylinder. Fixed up and ready for the trails.

04/17/2026

This '14 Subaru was towed in after sitting for a while.. Spiders everywhere on this dirt road driven gosh dang Colorado Cadillac!! The car was building up pressure in the cooling system,.... typical subaru things.. Customer decided to just have me put a low mileage used engine AND transmission from Colorado jdm engines. This car has a lot of miles on it but it came out super clean. This car will be good for another 200,000 miles if it can keep hub bearings in it..

04/16/2026

Had this sublime green 💚 17' Ram 1500 in the shop for a check over and a "Curtis Special" exhaust. Performed an oil change, front cv axle and front brake job and cabin air filter while it was in. Car wash with is a must! Thankful is an understatement for how busy the shop has been lately. Sound clip in comments.

04/15/2026

This beautiful 16' supercharged Mustang was towed in by the customer, thinking it was some severe/ catastrophic failure. The car would not start and when it did it was blowing smoke and very rich and obviously something was very wrong. After an under the bridge rip he did (we all do it) one of the charge pipes came loose right at the mass air flow sensor. After the customer was attempting to start it a few times it also fouled the spark plugs and definitely needed an oil change. Accompanied by some NGK Spark Plugs and followed up with a car wash with some this unit is going back to its owner clean and running the way it should.

04/07/2026

Good Ole Savana Van came in for a lifter noise that turned into an engine replacement. The oil that was in the filter looked like silver fingernail polish. The customer decided to go new, instead of doing cam and lifters (wise choice). At over 207,000 miles of service this 4.8 owes this van nothing! A reman 4.8 from Powertrain Products Inc checked in for duty! New radiator due to the oil cooler being contaminated as well as oil cooler lines to complete the package. Running great and back into service!

03/29/2026

Been a while since I've posted. We're still here and putting in a heavy amount of work. But feel free to give us a shout if you're in need. Thank you for looking!

07/25/2024

We talking home measurements or shop measurements...? 🫠😁🙃

07/23/2024

Been over a year since Myself or anyone I had "helping" run the social media has posted anything on here... Time flies! I'd be lying if I didn't say how rough of a year it's been with delays, deaths, constant price increases on supplies, shop overhead, shipping battles, etc, it's been unreal. But we're still here and surviving. .

Everyone keeps saying I need to increase my labor rate but how fair is that to everyone else, that are more than likely dealing with the same things in their line of work.? Simply put, I can't and won't. I've been at $125.00/ shop hour for over 2 years and will stay that way as long as I possibly can..

As per a conversation I was engaged in with other business owners, I already know that in this day and age, a business will not succeed without a footprint in social media which I have always neglected, unfortunately. I'm going to do my best to keep up on the Socials and keep engaged with everyone and everything as much as I can. I WILL do better.
Thank you.
-Curtis

Vehicle customisation shop

06/05/2023

HAPPY MONDAY PEOPLE! 👋😁
Hope it's the beginning of a GREAT week for everyone! 👍😃😎

05/24/2023

😁🤩🤗😄😃

05/23/2023

We are a Taco Tuesday family.. EVERY Tuesday! 🌮🌮

How about you?