Elan Power Products

08/31/2026

Barber Motorsports Park, SCCA Super tour.
The six fastest cars on the property were Elan Powered.
It’s an honor to be chosen by the best teams in sports car racing.

08/10/2026

Congrats Harbir and the entire Khill operation.
We are proud to be a part of this.

https://www.facebook.com/share/19KUFfbs66/?mibextid=wwXIfr

07/31/2026

Super well written article, check it out if for a little insight on how we operate.

https://www.enginelabs.com/tech-stories/engine-tech-stories/elan-power-products-builds-a-10000-rpm-naturally-aspirated-coyote/?fbclid=IwdGRjcATY1TxwZG9mAWZkaWQWULk_4faY8uVdvF1qs5p-oNAz5EYm9GV4dG4DYWVtAjExAHNydGMGYXBwX2lkCjY2Mjg1NjgzNzkAAR5EZFtAEE9h04NKWnNbMQQJlYjZajVOC9epCnBT7WWDT0J-ilUYwo_QgiC3gA_aem_KmLqDeKuNzBqlOwGaFgp2g

Elan Power built a 10,000-rpm N/A Coyote for Carlos Sobrino, that is currently the world's quickest and fastest.

07/14/2026

A couple of our engine programs use this Mazda, forged crank.
They come in with and Ra over three.
We polish them with a quick 600/800/1000 belt and we reduce the Ra by two thirds.
Less than one ten/thousandth of material is removed.
The nitrided billet cranks we use in most programs will go < 1 Ra.

07/14/2026

Nicely done video if you’d like to nerd out on Mirl’s Pikes Peak open wheel effort.
He drove his ass off for top 10 overall.

I catch up with Mirl Swan for a deep dive into his Swift 016 Atlant...

07/09/2026

Here are some more pics of Carlos Sobrino’s engine.
It is a 335 ci, coyote ford based off the castings Carlos supplied.
We have no idea what generation coyote. We had never seen a coyote ford before this one.
There’s nothing secret about it.
It’s as straight forward as can be, quality parts from vendors we have used for nearly thirty years.
The changes for this build are-
Iron ford racing block, a little more intake port volume(for methanol), revised(bigger) exhaust port, a touch more radial valve pocket clearance, a touch more piston to head clearance(for the iron block).
The Dailey pump looks perfect inside - we just mag the shafts and change the bearings and seals.

07/07/2026

What a successful past few weeks it has been for our great customers.
Different cars, engines, drivers, tracks, sanctioning bodies, countries - all doing the same thing.

Winning.

07/01/2026

3 horsepower per cubic inch, naturally aspirated, is uncharted territory for us.
Carlos Sobrino’s coyote ford was close before and now it’s back for a tune up.
Part of this upgrade is looking for flow in the heads. Nearly all the overhead engines we do it’s fairly easy to get the flow required.

Most of our overhead cam stuff has camshafts the are .4~valve lift/valve diameter.
This engine is more like .45.
So on a whim, I’ve treated this more like a high lift pushrod head. .big bowls, steep bowl blend angle, big long top angle.
It did exactly what I expected. It lost a chunk of flow below .350” and takes off at .450” valve lift.

Billy’s design is real easy off the seat and the overlap lift is quite low, but after that it goes medieval and rockets open and dwells like a NHRA stocker. 
Good stuff but I wouldn’t call it development. Its grip/rip/ship.
God speed

07/01/2026

You know you’re getting old when every workstation that I use is fitted with a lit, magnifying glass.
To be fair, getting this right is hard to see.