Kaiser Performance

Kaiser Performance Kaiser Performance has been around since 2003 doing basic differential rebuilds to re gearing, L*D, spools, 9" ends, narrowing and straightening.
(1)

06/19/2026

It's always good to learn something new. I'll be adding this to the list of things to check when doing axles with dropout third members. A little pressure test with some soapy water works great.

The cause will be in the comments.

GM 7.5" done with 28 spline Eaton Truetrac, 4.10 gears, 28 spline 1541h axle shafts, 1350 yoke, TA girdle cover and bear...
06/19/2026

GM 7.5" done with 28 spline Eaton Truetrac, 4.10 gears, 28 spline 1541h axle shafts, 1350 yoke, TA girdle cover and bearings throughout going into an LS powered 87 Caprice Classic.

Can anyone ID this rear end? 😂
06/17/2026

Can anyone ID this rear end?
😂

Ford 8.8 done with FRP 3.73 gears, Carbon L*D clutch kit, axle shaft and bearings throughout going into this turbo LS po...
06/16/2026

Ford 8.8 done with FRP 3.73 gears, Carbon L*D clutch kit, axle shaft and bearings throughout going into this turbo LS powered 71 Blazer.

Dings!! The displaced metal always causes high spots and have to be knocked down otherwise you'll have ring gear run out...
06/16/2026

Dings!! The displaced metal always causes high spots and have to be knocked down otherwise you'll have ring gear run out.

GM 10 bolt 8.5" done with a 30 spline Yukon Duragrip, Motive 3.42 gears, 1310 yoke, 30 spline 1541H axle shafts, spring...
06/16/2026

GM 10 bolt 8.5" done with a 30 spline Yukon Duragrip, Motive 3.42 gears, 1310 yoke, 30 spline 1541H axle shafts, spring perches, diff cover and bearings throughout going into this 55 Chevy.

Toyota IFS front axle refreshed and going into this 01 Land Cruiser.
06/12/2026

Toyota IFS front axle refreshed and going into this 01 Land Cruiser.

Chrysler 8 3/4" done with a Sure grip, 3.23 gears, bearing kit and grade 8 cap bolts going into a 57 Desoto.
06/06/2026

Chrysler 8 3/4" done with a Sure grip, 3.23 gears, bearing kit and grade 8 cap bolts going into a 57 Desoto.

Ford 9" done with big bearing billet ends, drain plug bung/jack pad, straightened tubes, 1541H 31 spline axles, 3.89 US ...
06/06/2026

Ford 9" done with big bearing billet ends, drain plug bung/jack pad, straightened tubes, 1541H 31 spline axles, 3.89 US gears, Yukon Duragrip, billet side adjusters and Timken bearings throughout going into this 351W/AOD powered 33 Ford.

Ford 8.8 done with Richmond 3.90 gears and bearing kit going into this 62 Falcon.
06/02/2026

Ford 8.8 done with Richmond 3.90 gears and bearing kit going into this 62 Falcon.

Address

3950 SW 208th Court
Beaverton, OR
97078

Opening Hours

Monday 9am - 5pm
Tuesday 9am - 5pm
Wednesday 9am - 5pm
Thursday 9am - 5pm
Friday 9am - 5pm

Telephone

+15033695037

Website

Alerts

Be the first to know and let us send you an email when Kaiser Performance posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category