Werk’s PWC & Off-road

Call Directions Contact the business

Werk’s PWC & Off-road I specialize in repair and rebuilds for 2 and 4 stroke PWCs, dirt bikes, atvs, and power equipment.

Been a busy summer…..just getting around to posting some project pictures.Brought an old 400ex back to life.Yamaha waver...
10/07/2026

Been a busy summer…..just getting around to posting some project pictures.

Brought an old 400ex back to life.

Yamaha waverunner ingested a boulder and stripped out the drive shaft coupler.

Numerous Seadoos with trashed wear rings.

12/09/2025

Quick valve job for this Yamaha Grizzly, I’m not sure if the last guy measured the lash with a tape measure or yard stick, either way he was 180 degrees off

A much needed tune up for this ‘03 Seadoo GTI LE. I rebuilt and tuned the carb that has never been opened up, adjusted t...
09/07/2025

A much needed tune up for this ‘03 Seadoo GTI LE. I rebuilt and tuned the carb that has never been opened up, adjusted the oil pump, new starter, spark plugs, and replaced the leaking fuel selector valve.

Just finished putting a high performance impeller in a returning customer’s ‘03 GPR800. Old impeller was a little beat u...
07/24/2025

Just finished putting a high performance impeller in a returning customer’s ‘03 GPR800. Old impeller was a little beat up from some rocks but the wear ring is still tight, actually threw some sparks out when I started it up.

06/22/2025

‘86 Evinrude alive again

It’s not often that I work on boat motors, but this ‘86 Evinrude is some freshly rebuilt carbs and is ready to hit party...
06/22/2025

It’s not often that I work on boat motors, but this ‘86 Evinrude is some freshly rebuilt carbs and is ready to hit party cove.

Just finished fixing up two 1997 Seadoo XP’s that had been previously worked on by a shade tree mechanic. One was missin...
06/18/2025

Just finished fixing up two 1997 Seadoo XP’s that had been previously worked on by a shade tree mechanic. One was missing a couple exhaust manifold bolts, so they just caked the exhaust gasket with silicone (but it still leaked), it also had one Rave valve turned the wrong direction so it would not function, and carbs weren’t tuned correctly. On the other one, the needle seat levers were bent so the pop-off pressure was very low and would flood the engine, also the low speed screws weren’t tuned correctly.

First one in the books for 2025. This Yamaha FX-140 got a new wear ring and impeller.
04/04/2025

First one in the books for 2025. This Yamaha FX-140 got a new wear ring and impeller.

This ‘03 GP800r was my last big project for the season. It recently had the engine rebuilt TWICE and the carbs “rebuilt”...
10/26/2024

This ‘03 GP800r was my last big project for the season. It recently had the engine rebuilt TWICE and the carbs “rebuilt”. It had a dead cylinder. I found it had dropped a power valve and damaged the piston. When I had the engine apart I noticed the screws on the carbs had never been removed. So I rebuilt the carbs and put new oil lines on it.

‘99 XP Limited came in with the classic 5amp computer fuse blowing. I found the bendix spur gear had some broken teeth t...
10/01/2024

‘99 XP Limited came in with the classic 5amp computer fuse blowing. I found the bendix spur gear had some broken teeth that stuck to the magneto then did some damage to the stator. Also found the front piston was melted down from a lean condition caused by a leaking crank seal. So it got new pistons and bore, I replaced the restrictive air box with Pro K flame arresters, changed jetting, and put carbon tech reeds in it.

Address

Baldwin City, KS

Telephone

+17857664544

Website

Alerts

Be the first to know and let us send you an email when Werk’s PWC & Off-road posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Werk’s PWC & Off-road:

Shortcuts

Share

Category