Innovative MotoSports

Call Directions Website

Innovative MotoSports all things moto. custom cafe bikes, vintage motorcycle repair & restoration.

Please note, we are appointment only and am currently scheduling 7-8 weeks out of as of 5/19/20

Brakes and forks for the vfr800. Cb466f motor is almost ready to go home. X-pro 125 with a no spark issue fixed and o...
08/09/2026

Brakes and forks for the vfr800. Cb466f motor is almost ready to go home. X-pro 125 with a no spark issue fixed and out the door

One camshaft away from finishing this cb466. ACME Moto killed it with v***r blasting the cases and all covers. This is...
08/08/2026

One camshaft away from finishing this cb466. ACME Moto killed it with v***r blasting the cases and all covers. This is built to same specs as Goldie’s motor I built. 466 big bore, jmr ported head, webco cam, kibble white valve springs, lightened crank, ape cylinder studs, shot peened rods, cb750 rod bolts, dyna ignition, ebc clutch pack and springs, ttr400 cam chain adjuster.

The nsr500v tecmas elf rep is just about done. Just couple more carbon bits for the gauges and out a few more miles on i...
07/20/2026

The nsr500v tecmas elf rep is just about done. Just couple more carbon bits for the gauges and out a few more miles on it.

All loaded up and ready for round 4 at Kahoka Saturday. Gonna be a hot one
07/17/2026

All loaded up and ready for round 4 at Kahoka Saturday. Gonna be a hot one

Sometimes a simple hey probably just need to go through carbs turns into a whole lot of fun. This cx500 was one of thos...
07/17/2026

Sometimes a simple hey probably just need to go through carbs turns into a whole lot of fun. This cx500 was one of those. Started there, then valves needed adjusted, aftermarket ignition issue, then starter clutch gave up, so out comes the motor, then back in and a new issue with the ignition module and two bad diodes, then finally got it all dialed it and ready to rip.

This Yamaha went in with leaking fuel t’s on carburetor assembly to another shop. It left there being told the middle c...
07/11/2026

This Yamaha went in with leaking fuel t’s on carburetor assembly to another shop. It left there being told the middle cylinder would be dead and it needed 3-5k to fix it. The owner did his own compression test and found all three were the same and dropped it off. Cylinder 3 wasn’t firing and it was because it wasn’t getting fuel. Rebuilt the carbs, set the float height, synced them and it’s running like it should now.

I don’t post as much as I used to, but keeping bikes rolling out of the shop still. New set of bodywork for a r6, fixed...
06/25/2026

I don’t post as much as I used to, but keeping bikes rolling out of the shop still. New set of bodywork for a r6, fixed a non latching reverse button on a Goldwing, and in the home stretch with a cb400f motor built to same specs as Goldie.

This kz1000 has been seen some miles in her life. With over 47k miles on the odometer it was ready for a fresh top end....
12/23/2025

This kz1000 has been seen some miles in her life. With over 47k miles on the odometer it was ready for a fresh top end. .5mm over bore pistons, valve job and head gone through, new cam chain rollers, removed the emissions items and made sure the coils are getting a proper 12volts and it’s ready to ride.

Address

Nw 84th Avenue
Ankeny, IA
50023

Telephone

+15152309938

Website

Alerts

Be the first to know and let us send you an email when Innovative MotoSports posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category