Magicmotorsport Afrique

02/12/2025

OBD, OBD on Bench, and Boot

Version 7.42.0.0 of Flex out now introducing full support to Magneti Marelli 8GMC control units installed on American market Fiat 500 cars.



Program via the diagnostic port: read, make your modifications (like power increase) and write your file directly on the control unit.



If the vehicle is not available, you can work in OBD on Bench and program the ECU via connector.



In order to clone or recover the unit, you can operate in Bootloader, too, by opening the unit and connecting to the PCB.



Some of the supported vehicles:
Check all supported vehicles
Fiat 500 (312) 1.4L MultiAir 16v 102PS

Fiar 500 (312) 1.4L Fire 16v 102PS

This new protocol is available for the following software packages:
OBD
FLS0.1M – SW Flex ECU (car, van, bike) OBD/Bench Master

FLS0.1S – SW Flex ECU (car, van, bike) OBD/Bench Slave

FLS0.5M – SW Flex Full Master

FLS0.5S – SW Flex Full Slave

BOOT
FLS0.4M – SW Flex Boot Nexus MPC5### Master

FLS0.4S – SW Flex Boot Nexus MPC5### Slave

FLS0.5M – SW Flex Full Master

FLS0.5S – SW Flex Full Slave

Buy Software
Newly added protocols:
OBD
FCA Marelli 8GMC MPC5565 Read/Write/Checksum Calculation Internal Flash

Writing Time
~2 minutes
Reading Time
~2 minutes
BOOT
FCA Marelli 8GMC MPC5565 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup, Clone

Flex Full Support FCA Marelli 8GMC. New Magicmotorsport release introducing full support to Magneti Marelli 8GMC control units installed...

18/11/2025

Yamaha in OBD

New release of Flex, version 7.41.0.0, adding support to Denso control units with RH850 processor installed on models such as T-Max, R1, and MT-09 with the new Flex protocol for Yamaha Motorbikes.



Program via the diagnostic port: just carry out the Virtual Read, make your modifications like increasing power or removing DTCs, then write the file directly on the control unit.



In order to work in OBD, you need our FLX2.68 cable compatible with the newest EU5 and EU5+ motorcycles from brands such as Ducati, Honda, Suzuki, KTM, Harley, Yamaha, Aprilia, Kawasaki 6pin.

21/08/2025

Flex Version 7.30.0.0 Released The new OBD protocol has been released for managing the map area of Bosch MG1CS036 ECUs (including those equipped with the latest anti-tuning protections). With this solution, you can operate directly through the diagnostic port, working easily and safely without ha....

21/08/2025

New Full OBD Protocol has been released for programming the Denso 112300-5920 engine control unit on the Suzuki Grand Vitara.

03/06/2025

🏍 New Flex solution for two wheels and quads 🏍
Welcome Delphi MT05, MT05.2, and MT05.3 ECUs
🪢 Flex OBD for MT05 MT05.2 and MT05.3
New Flex solution for two wheels and quads
Download the latest version of the Flex software to program two-wheel vehicles and quads in OBD.
With this new release, Delphi MT05, MT05.2, and MT05.3 control units are now supported, specifically those installed on a wide range of motorcycles branded Benelli, CF Moto, QJ Motor, SWM Motorcycles, and many more.
The new OBD protocol allows full read of the Flash memory and to write the map area via the diagnostic socket of the vehicle or connections to the connector.
Moreover, thanks to the Recovery via HW function, the ECU can now be restored even in complex situations, such as in case a corrupted or unsuitable file has been written on the engine unit: this feature automatically activates in case of connection errors.
Supported Vehicles
Check all supported vehicles
Benelli 752S 75PS
Benelli BN600 86PS
CF Moto CForce 850XC 65PS
QJ Motor Flash 300S 31PS
SWM Motorcycles 500R 35PS
New protocol available for the following software packages:
OBD
FLS0.1M – SW Flex ECU (car, van, bike) OBD/Bench Master
FLS0.1S – SW Flex ECU (car, van, bike) OBD/Bench Slave
FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
FLS0.13M – SW Flex Bikes OBD/Bench/Boot Master
FLS0.13S – SW Flex Bikes OBD/Bench/Boot Slave
Buy Software
Newly added protocols:
OBD
All Delphi MT05 C164CM (KWP) Read Internal Flash, Write/Checksum Calculation Maps
All Delphi MT05.2 C164CS (KWP) Read Internal Flash, Write/Checksum Calculation Maps
All Delphi MT05.3 SPC572L (UDS) Read Internal Flash, Write/Checksum Calculation Maps
Writing Time
~20 seconds
Reading Time
~1 minute
Bug fixes:
Fixed CRC type on FCA Marelli MM10JA

Flex OBD for MT05 MT05.2 and MT05.3. With this new release, Delphi MT05, MT05.2, and MT05.3 control units are now supported, specifically...

13/05/2025

💣💣 SID212 & SID212 EVO are now officially supported 💣💣
🚀 It’s here...and it’s yours
😄 The wait is over

👏Skill and dedication that truly make a difference
Special thanks to Faheem Adam of Adam Engineering for the technical contribution

😮This is just the beginning of a new wave of exclusive solutions

Stay Tuned

🔒OBD Protocol and new RFT™(Ready for tuning) service available starting from May 21

Come visit us at Autopromotec Bologna Hall 30 - Stand A84 and discover the most requested exclusive solution on the market

🚗 Exclusively Free for all active Full license holders 🚗

06/05/2025

Second Batch of Flex Heavy-Duty Protocols

New Flex Update Out Now with the Second Batch of Flex Heavy-Duty Protocols
Second batch of protocols for heavy-duty vehicles released on Flex.

This new version of Flex (7.21.0.0) expands support to control units installed on industrial vehicles, agricultural machinery, and trucks, introducing new solutions in Bench and enriching compatibility in Boot for many ECUs that could once be programmed only via OBD or Bench.

This new release, dedicated to the second batch of protocols for heavy-duties, enables read and write operations, as well as full cloning – when available – of all memories inside control units, thanks to Bench and Boot modes.

Here’s the list of new available supports on Flex:

Denso 275700-4890 in Bench
Denso 275700-1201 in Bench
Landini Bosch MD1CS069 in Bench
Isuzu Bosch MD1CC878 in Bench
Isuzu Bosch MD1CE108 in Bench
Mercedes Truck Continental CPC3EVO in Boot
Freightliner Truck Continental CPC4 in Boot
Cummins CM2100A in Boot
Cummins CM2150C in Boot
Cummins CM2150E in Boot
Cummins CM2200A in Boot
Cummins CM2200B in Boot
Cummins CM2220A in Boot
Cummins CM2220B in Boot
Cummins CM2220C in Boot
Cummins CM2880 in Boot
This new protocols are available for the following software packages:

Bench/Boot

FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
FLS0.15M – SW Flex Heavy Duty OBD/Bench/Boot Master
FLS0.15S – SW Flex Heavy Duty OBD/Bench/Boot Slave
Newly added protocols:

(Bench)

Landini Bosch MD1CS069 TC299 Read/Write/Checksum Calculation Internal Flash, Read/Write Internal EEPROM, Full Backup
Isuzu Bosch MD1CC878 SPC58 Read/Write/Checksum Calculation Internal Flash, Read/Write Internal EEPROM, Full Backup
Isuzu Bosch MD1CE108 SPC58 Read/Write/Checksum Calculation Internal Flash, Read/Write Internal EEPROM, Full Backup
Kubota Denso 275700-1201 SH7058 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
Kubota Denso 275700-4890 SH7058 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
(Boot)

All Cummins CM2100A MPC5554 Read/Write/Checksum Calulation Internal Flash
All Cummins CM2150C MPC5554 Read/Write/Checksum Calulation Internal Flash
All Cummins CM2150E MPC5566 Read/Write/Checksum Calulation Internal Flash
All Cummins CM2200A MPC5566 Read/Write/Checksum Calulation Internal Flash
All Cummins CM2200B MPC5566 Read/Write/Checksum Calulation Internal Flash
All Cummins CM2220A MPC5566 Read/Write/Checksum Calulation Internal Flash
All Cummins CM2220B MPC5566 Read/Write/Checksum Calulation Internal Flash
All Cummins CM2220C MPC5566 Read/Write/Checksum Calulation Internal Flash
All Cummins CM2880 SPC5644A Read/Write/Checksum Calulation Internal Flash
Mercedes Trucks Continental CPC3EVO MPC5674 Read/Write/Checksum Calulation Internal Flash, Read/Write External EEPROM, Full Backup
Freightliner Trucks Continental CPC4 TC1796 Read/Write/Checksum Calulation Internal Flash, Read/Write Internal EEPROM, Read/Write External EEPROM, Full Backup
Bug Fixes:

Added new CRC type for All Cummins CM2350
Added new CRC support for Aston Martin Bosch ME17.8.31
Added new CRC type for Mazda Denso P###
Added new CRC type for Suzuki Denso SH7058
Added new type for FCA Continental GPEC2
Fixed CRC problem in VAG Bosch EDC17CP44
Fixed reading error in some version of Cummins CM2220
Click here to discover the full list of supported vehicles.

Second Batch of Flex Heavy-Duty Protocols. This new version of Flex expands support to control units installed on industrial vehicles...

31/03/2025

Flex OBD Solution for Continental GPECx

Version 7.17.0.0 of Flex Out Now with a Flex OBD Solution for Continental GPECx
New release on Flex dedicated to OBD programming: a Flex OBD solution for Continental GPECx, specifically GPEC2, GPEC2A, GPEC3, GPEC4, GPEC4LM engine units.

Just unlock the unit in Boot mode and then proceed with reading and writing the map area directly via the diagnostic port of the vehicle.

Thanks to the newest update of Flex, removing the ECU every time to modify engine parameters is no longer necessary: unlock your control unit in Boot mode and then go for OBD any other time.

Some of the supported vehicles:

Chrysler 200 2.4L 180PS
Dodge RAM Promaster City 2.4L 180PS
Fiat Tipo I 1.0L Multiair 120PS
Fiat Toro 2.4L Multiair II 185PS
Jeep Compass 2.4L 180PS
Jeep Renegade 1.3L Multijet 150PS
This new protocol is available for the following software packages:

OBD

FLS0.1M – SW Flex ECU (car, van, bike) OBD/Bench Master
FLS0.1S – SW Flex ECU (car, van, bike) OBD/Bench Slave
FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
Newly added protocols:

(OBD)

FCA Continental GPEC2 MPC5566 Read/Write/Checksum Calculation Maps, Read External EEPROM
Reading Time : ~ 7 minutes Writing Time : ~ 4 minutes
FCA Continental GPEC2A MPC5674F Read/Write/Checksum Calculation Maps, Read External EEPROM
Reading Time : ~ 10 minutes Writing Time : ~ 5 minutes
FCA Continental GPEC3 MPC5674F Read/Write/Checksum Calculation Maps, Read External EEPROM
Reading Time : ~ 10 minutes Writing Time : ~ 5 minutes
FCA Continental GPEC4 MPC5674F Read/Write/Checksum Calculation Maps, Read External EEPROM
Reading Time : ~ 10 minutes Writing Time : ~ 5 minutes
FCA Continental GPEC4LM MPC5674F Read/Write/Checksum Calculation Maps, Read External EEPROM
Reading Time : ~ 10 minutes Writing Time : ~ 5 minutes
Bug fixes

Fixed writing error in Bosch MG1UA008
Added new CRC type for All Continental M3C
Added new CRC type for Tata Delphi DCM7.1AP
Software improvements

Added OBD Support for All Bosch MSE8.0
Added support for VAG Bosch MG1CS008 SFD2
Click here to discover the full list of supported vehicles.

Flex OBD Solution for Continental GPECx. New release on Flex dedicated to OBD programming of Continental GPEC2, GPEC2A, GPEC3...

21/02/2025

Solution exclusive pour VAG 2.0 TFSI (MG1CS031)

Version 7.14.0.0 de Flex prête
Les sorties dédiées aux unités de contrôle VAG MDG1 protégées par les derniers systèmes anti tuning ne sont pas finies. À partir d’aujourd’hui, Flex introduit un protocole exclusif pour le déverrouillage et la programmation en OBD des calculateurs Bosch MG1CS031 installés sur les véhicules VAG équipés d’un moteur à essence 2.0L TFSI, produits à partir de juillet 2020.

Comme pour les sorties précédentes pour les unités MDG1, cette nouvelle solution permet et l’écriture de la zone des cartes (Maps) et de l’application software (Maps & Code).

Téléchargez la lecture virtuelle de notre banque de données, faites votre personnalisations et optimisez les performances des moteurs à essence du groupe VAG.

Notez bien: Notre système de sécurité avancé ensure la protection des données de l’entreprise; par conséquent, la connection à internet est obligatoire pour toutes les opérations d’écriture.

Certains des véhicules pris en charge:

Audi A3 2.0L TFSI 190PS
Audi A4 2.0L TFSI 150PS
Audi A5 2.0L 35TFSI 150PS
VW Polo GTI 2.0L TSI 207PS
Le nouveau protocole est disponible pour les paquets logiciels suivants:

OBD

FLS0.1M – SW Flex ECU (car, van, bike) OBD/Bench Master
FLS0.1S – SW Flex ECU (car, van, bike) OBD/Bench Slave
FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
Les nouveaux protocoles ajoutés:

(OBD)

VAG Bosch MG1CS031 TC299TP Virtual Read/Write/Checksum Calculation Maps, Virtual Read/Write/Checksum Calculation Maps & Code
Temps d’écriture: ~ 2 minutes
Cliquez ici pour consulter la liste complète des véhicules pris en charge.

Solution exclusive pour VAG 2.0 TFSI (MG1CS031). Les sorties dédiées aux unités de contrôle VAG MDG1 protégées par les derniers...

05/02/2025

Exclusive for VAG 3.0L TDI (MD1CS014)

Version 7.12.0.0 of Flex Out Now With an Exclusive for VAG 3.0L TDI
New exclusive for VAG 3.0L TDI out now on Flex to unlock and program in OBD mode Bosch MD1CS014 engine units with the latest anti tuning protections.

Thanks to this new Flex solution, you no longer need to remove the ECU from VAG vehicles with 3.0L TDI engines, produced from July 2020 on: just download the virtual read from our database and unlock the control unit.

This protocol allows you to choose whether to only write maps (Maps) or use the Write Maps and Code function for ASW + Maps full programming.

This software update paves the way to a release series dedicated to (Locked) VAG MDG1 control units.

Moreover, after downloading the Virtual Read from the Flex software, you can now upload it directly on StageX and use DTC Removal algorithms, Mappacks, as well as new AI solutions:

AI Stages
Diesel Particulate Filter (DPF) Deactivation
Exhaust Gas Recirculation (EGR) Deactivation
Readiness Calibration
Lambda Sensor Deactivation
Oil Pressure Fix
Selective Catalytic Reduction (SCR) Deactivation
Start-Stop Inversion
Start-Stop Deactivation
Please note: our new security system ensures company data protection; therefore, an internet connection is mandatory for all writing operations.

Some of the supported vehicles:

Audi A6 3.0L 45TDI V6 250PS
Audi A8 3.0L 50TDI V6 290PS
Audi Q7 3.0L 50TDI V6 290PS
Audi SQ5 3.0L 50TDI V6 345PS
Volkswagen Touareg 3.0L 50TDI V6 290PS
This new protocol is available for the following software packages:

OBD

FLS0.1M – SW Flex ECU (car, van, bike) OBD/Bench Master
FLS0.1S – SW Flex ECU (car, van, bike) OBD/Bench Slave
FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
Newly added protocols:

(OBD)

VAG Bosch MD1CS014 TC299TP Virtual Read/Write/Checksum Calculation Maps, Virtual Read/Write/Checksum Calculation Maps & Code
Writing Time: ~ 2 minutes
Bug fix

Fixed writing error of the External EEPROM for FCA Marelli MM10JA
Software improvements

Added new type version for Renault Continental SID321
Added Bench support for Piaggio Bosch ME17.9.21 TC1724N
Added Bench support for MG Bosch ZS 2024 MED17.8.10.1
Added Boot Support for Stellantis Delphi DCM7.1P
Click here to discover the full list of supported vehicles.

Exclusive for VAG 3.0L TDI (MD1CS014). New exclusive out now on Flex to unlock and program in OBD mode Bosch MD1CS014 engine units...

16/12/2024

New Solutions for Ducati, Husqvarna, and KTM

Version 7.9.0.0 of Flex Out Now with new Solutions for Ducati, Husqvarna, and KTM
Download the latest version of Flex and program Continental M4C engine units in OBD Full, Bench, and Boot, enjoy the new solutions for Ducati, Husqvarna, and KTM.

These protocols allow you to read and write the whole content of the Flash memory, with virtualized EEPROM: you can now restore damaged units, writing the backup from a source unit to a destination unit in function.

Thanks to the newest release of Magicmotorsport (version 7.9.0.0), the list of motorcycles supported by Flex becomes more and more numerous, and as of today you can even modify performance of vehicles such as Ducati Hypermotard 950, Husqvarna TC250, and KTM SX 300.

Optimize engine parameters and get the best out of your two-wheel vehicle.

*Please note: for the OBD Full mode, you need to use the dedicated FLX2.68 cable.

Some of the supported vehicles:

Ducati Hypermotard 950cc 115PS
Ducati Scrambler 800cc 73PS
Husqvarna TC 125cc 38PS
Husqvarna TC 250cc 54PS
KTM SX 125cc 16PS
KTM XC 57PS
This new protocol is available for the following software packages:

OBD Full/Bench

FLS0.1M – SW Flex ECU (car, van, bike) OBD Full/Bench Master
FLS0.1S – SW Flex ECU (car, van, bike) OBD Full/Bench Slave
FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
FLS0.13M – SW Flex Bikes OBD Full/Bench/Boot Master
FLS0.13S – SW Flex Bikes OBD Full/Bench/Boot Slave
Boot

FLS0.4M – SW Flex Boot Nexus MPC5### Master
FLS0.4S – SW Flex Boot Nexus MPC5### Slave
FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
FLS0.13M – SW Flex Bikes OBD Full/Bench/Boot Master
FLS0.13S – SW Flex Bikes OBD Full/Bench/Boot Slave
Newly added protocols:

(OBD Full e Bench)

Ducati Continental M4C SPC563M Read/Write/Checksum Calculation Internal Flash (EEPROM virtualized), Clone/Restore
Reading Time : ~ 40 seconds Writing Time : ~ 1 minute

(Boot)

Ducati Continental M4C SPC563M Read/Write/Checksum Calculation Internal Flash (EEPROM virtualized), Clone/Restore
Reading Time : ~ 30 seconds Writing Time : ~ 40 seconds

Bug fixes:

Added new CRC type for Porsche Bosch ME7.8
Added new CRC type for Mercedes Continental ACM2.1
Software improvements:

Added Bench support for Mini Bosch MEV17.2.2 TC1767
Click here to discover the full list of supported vehicles.

New Solutions for Ducati Husqvarna and KTM. Download the latest version of Flex and program Continental M4C engine units in OBD Full...

21/10/2024

Boot Solutions for Old School ECUs
Version 7.5.0.0 of Flex Out Now with Boot Solutions for Old School ECUs
This new update is 100% dedicated to boot solutions for Old School protocols. Flex’s vehicle list enriches with 17 new supports in bootloader mode, including FCA, VAG, and PSA.
With the version 7.5.0.0 of Flex, we ensure you can program even engine units from past generations that are still widespread.
Below the units supported by Flex:
FCA Marelli IAW 4AF
Ford Delphi DCU101
Isuzu Denso 4HK1
Kia/Hyundai Bosch M7.9.8
Mercedes Bosch ME2.7.1
Opel Bosch ME7.6.4
PSA Bosch ME7.4.9
PSA Bosch M7.4.4
PSA Bosch EDC15C7
PSA Siemens SID804
PSA Siemes SID801
Renault Siemens EMS3132
Toyota Bosch M7.9.5
Toyota Bosch ME7.9.51
VAG Marelli IAW 4HV
VAG Siemens Simos9.1
VAG Bosch ME7.5.30
Some of the supported vehicles:
Fiat Fiorino 146 1.3L 60PS
Opel Astra 1.6L Turbo 192PS
Toyota Aygo 1.0L 67PS (2005)
Peugeot Manager 2.8L HDI 128PS (2000)
Volkswagen Fox 1.6L 105PS (2003)
These new protocols are available for the following software packages:
Boot (ME2.7.1 – M7.4.4 – EDC15C7 PSA – SIMOS9.1 – EMS3132 – SID804 PSA – SID801 PSA)
FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
FLS0.7M – SW Flex Boot Infineon C165/166/167 Master
FLS0.7S – SW Flex Boot Infineon C165/166/167 Slave
Boot (IAW 4HV – IAV 4AF – ME7.9.51 – ME7.4.9 – M7.9.5 – M7.9.8 – ME7.5.30 – ME7.6.4 – DCU101)
FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
FLS0.8M – SW Flex Boot ST10 Master
FLS0.8S – SW Flex Boot ST10 Slave
Boot (Denso 4HK1)
FLS0.5M – SW Flex Full Master
FLS0.5S – SW Flex Full Slave
FLS0.6M – SW Flex OBD/Bench/Boot Renesas SH7###x Master
FLS0.6S – SW Flex OBD/Bench/Boot Renesas SH7###x Slave
Newly added protocols:
(Boot)
FCA Marelli IAW 4AF ST10F269 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
Ford Delphi DCU101 ST10F276 Read/Write/Checksum Calculation Internal Flash
Isuzu Denso 4HK1 SH7059 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
Kia/Hyundai Bosch M7.9.8 ST10F275 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
Mercedes Bosch ME2.7.1 C167 Read/Write/Checksum Calculation External Flash, Read/Write External EEPROM, Full Backup
Opel Bosch ME7.6.4 ST10F276 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
PSA Bosch ME7.4.9 ST10F275 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
PSA Bosch M7.4.4 C167 Read/Write/Checksum Calculation External Flash, Read/Write External EEPROM, Full Backup
PSA Bosch EDC15C7 C167 Read/Write/Checksum Calculation External Flash, Read/Write External EEPROM, Full Backup
PSA Siemens SID804 C167 Read/Write/Checksum Calculation External Flash, Read/Write External EEPROM, Full Backup
PSA Siemes SID801 C167 Read/Write/Checksum Calculation External Flash
Renault Siemens EMS3132 C167 Read/Write/Checksum Calculation External Flash
Toyota Bosch M7.9.5 ST10F275 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
Toyota Bosch ME7.9.51 ST10F275 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
VAG Marelli IAW 4HV ST10F296 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
VAG Siemens Simos9.1 C167 Read/Write/Checksum Calculation External Flash, Read/Write External EEPROM, Full Backup
VAG Bosch ME7.5.30 ST10F275 Read/Write/Checksum Calculation Internal Flash, Read/Write External EEPROM, Full Backup
Bug fixes
Added new CRC type for Kia/Hyundai Kefico CPEGD3.20.1 OBD
Enjoy boot solutions for Old School ECUs, click here to discover the full list of supported vehicles.

Boot Solutions for Old School ECUs. This new update is 100% dedicated to Old School protocols. Flex’s vehicle list enriches with 17 new...