Devilsown Water/methanol Injection UK

Devilsown Water/methanol Injection UK Methanol Injection UK strives to be the #1 source for all your Methanol/Alcohol/Water Injection Syst Lower air temperatures by 50-200+ degrees.

DevilsOwns Benefits Include:

Increase horsepower safely by 10-15%. Decrease cylinder temperatures up to 300 degrees. Reduce the effects of heat soak in warmer climates. Allows you to safely run more boost and timing. Reduces carbon and helps maintain a clean combustion chamber. Increases octane at user programmable boost levels. The main function of water m**hanol injection is preventing deto

nation. Detonation is caused by high temperatures and pressure developed in the combustion chamber. Water has a high latent heat content, which makes it extremely effective at preventing the onset of detonation. Water injection also reduces the production of NOx (oxides of nitrogen). Methanol, with its 116 octane and high flash point, further reduces the chances of detonation. While water is not combustible, it has a greater capacity to cool the intake air temps more than m**hanol alone. This is why we recommend a 50/50 mixture being misted into your boosted engine. Methanol also effectively increases the octane rating of the fuel, allowing performance gains when used in supercharged and turbocharged applications.

11/08/2026

🔥 FORD RANGER RAPTOR 3.0 V6 – 550BHP 🔥

Another serious Raptor build through the doors at hexcode_tuning 💥

This one has just had a charge pipe m**hanol upgrade + direct-port m**hanol injection system installed, designed to support the power and keep intake temperatures under control when pushing the 3.0 V6 EcoBoost hard.

💧 Direct-port m**h injection
🧠 DevilsOwn DVS3 controller
🚨 Devilsown Failsafe protection
🏁 Race-spec m**h tank mounted in the rear
🔧 Custom installation throughout

And this isn’t an off-the-shelf setup — this is currently the only Raptor in the UK running this particular direct-port m**hanol setup. 🇬🇧

At around 550BHP, the 3.0 V6 is already seriously quick… and the m**h system gives us another level of control when the engine is under load. 🔥

Built for performance. Built properly.

HEXCODE TUNING
📍 Performance | Diagnostics | Tuning | Dyno

Just in case you were thinking of ordering a kit or some parts/upgrades or might need some brew to tie you over, get tho...
06/08/2026

Just in case you were thinking of ordering a kit or some parts/upgrades or might need some brew to tie you over, get those orders in 😉

New 2.5 gallon tank now available!*Dimensions 230mm High x 350mm Long x 200mm Wide*Comes with vented lid with 90mm openi...
10/06/2026

New 2.5 gallon tank now available!

*Dimensions 230mm High x 350mm Long x 200mm Wide
*Comes with vented lid with 90mm opening.

So It’s best suited for trunk placement.

This tank can be used for any alcohol water mix. It’s 100% m**hanol compatible. This tank features a 90mm opening for easy fill up. Cap is included.

**hanolinjection

The new DVS3 LCD screen progressive controller now available The DVS3 Progressive Controller from DevilsOwn is the lates...
13/03/2026

The new DVS3 LCD screen progressive controller now available

The DVS3 Progressive Controller from DevilsOwn is the latest technology we have to offer. Its compact, lightweight, and easy to install with a LCD screen. It’s designed to give your vehicle stable fluid pressure with a user adjustable range. It contains a high quality built in 4Bar MAP sensor (Boost version), a wide-ranging filtered power supply and a high current switching MOSFET transistor.

Controller General Operation:

*Unit will read/save START and END dial settings. (END Point is where Pump is fully on)

*Pump duty cycle is calculated based on saved dial settings and input reading.

*When input reading reaches the saved START setting, the pump will activate with a 20% duty cycle.

*Duty cycle will ramp up to 100% as input reading reaches the saved END point where the pump will remain fully on.

*The duty cycle percentage increases and is a direct correlation between the input reading (boost or voltage) and saved dial values. This means the pump output will be a completely analogue linear response.

*Optional dual stage (referred to as “Stage 2”)

**h **hanolinjection

30/01/2026

Devilsown stainless direct port kits, the perfect upgrade to your single nozzle set up. Full stainless line upgrades also available.

Brett’s cool Ford 300 inline 6 now packing our direct port set up **h **hanolinjection
08/01/2026

Brett’s cool Ford 300 inline 6 now packing our direct port set up

**h **hanolinjection

Christmas & New year sale now live on the webshop, go grab yourself a octane boosting new year treat
23/12/2025

Christmas & New year sale now live on the webshop, go grab yourself a octane boosting new year treat

Methanol Injection, Alcohol Injection, Water Injection, DevilsOwn

Offers go live on the site at midnight & run through to Monday night so be quick as once they end that’s it.
27/11/2025

Offers go live on the site at midnight & run through to Monday night so be quick as once they end that’s it.

Address

Mill Lane
Romsey
SO516

Opening Hours

Monday 8:30am - 6pm
Tuesday 8:30am - 6pm
Wednesday 8:30am - 6pm
Thursday 8:30am - 6pm
Friday 8:30am - 6pm
Saturday 8:30am - 6pm

Website

Alerts

Be the first to know and let us send you an email when Devilsown Water/methanol Injection UK posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Devilsown Water/methanol Injection UK:

Shortcuts

Share

Category