Dynodaze Rolling Road £50 Power Runs & Printout

Directions Website

Dynodaze Rolling Road £50 Power Runs & Printout Rolling Road Specialists £50 for 3 power runs and a printout! Dynodaze Ltd, PerformanceTuning & Remapping in Nuneaton and Hinckley area.

We can remap most makes and models of car. We can supply and fit any and all parts you require.

Curious to see what your car is really putting down? Join us at Dynodaze for our Saturday morning dyno sessions. Check o...
18/10/2026

Curious to see what your car is really putting down? Join us at Dynodaze for our Saturday morning dyno sessions. Check our Facebook Events section!

Whether you’ve just finished a new mod, tuned your daily, or simply want to settle a bet with your mates, our 2WD rolling road is set up and ready to test any front-wheel-drive or rear-wheel-drive setup.

The Details
When: Every Saturday, 8:30 AM – 12:00 PM

Price: £50

What’s Included: 3 full power runs plus a detailed physical printout to take home

Data Measured: Brake Horsepower (BHP), Wheel Horsepower (WHP), and Torque (ft-lbs)

The Vibe
Dynodaze runs a relaxed, welcoming, and family-friendly atmosphere. Come down, grab a spot, watch a steady stream of unique builds hit the rollers, and chat with fellow car enthusiasts while you wait your turn.

No ego, no pressure—just solid runs, accurate numbers, and good company. Pop down this Saturday and put your power to the pavement.

What started as a standard timing chain, guide, and tensioner replacement quickly turned into a much bigger job on this ...
11/08/2026

What started as a standard timing chain, guide, and tensioner replacement quickly turned into a much bigger job on this Honda CRX.

​First up, a massive oil leak led us to a PCV block held on by just ONE bolt out of four. To fix that properly, the supercharger had to come off... which opened up a whole new can of worms.

​Once the charger was off, we spotted a crack in the manifold. We got that welded up and faced flat before any rebuild could begin.

​But after eating our vegetables, we got to move on to dessert: fabricating a full custom 3-inch exhaust, including modifying the manifold collector to a full 3-inch!

​Safe to say this supercharged setup is going to breathe a lot better now. We gained 22bhp from.all this work the car is leaving us with 283 bhp .

​ MechanicLife Wrenching EngineRebuild

Fn2 in with us for a stage 1 remap
10/08/2026

Fn2 in with us for a stage 1 remap

Just a reminder the rolling road is closed today as we are all at Blyton Park for Javelin Sprint series.
01/08/2026

Just a reminder the rolling road is closed today as we are all at Blyton Park for Javelin Sprint series.

Ek9 with a k24 frank in for mapping , this was on stock ep3 cams with a 50 degree vtc wheel . Leaving us on 255 bhp .   ...
30/07/2026

Ek9 with a k24 frank in for mapping , this was on stock ep3 cams with a 50 degree vtc wheel . Leaving us on 255 bhp .

Fn2 in with us for remap . Car had a direnza induction kit and a japspeed twin exit 2.5" . Came in at 206 bhp leaving us...
22/07/2026

Fn2 in with us for remap . Car had a direnza induction kit and a japspeed twin exit 2.5" . Came in at 206 bhp leaving us at 213 bhp.

Fn2 in with us for remap . Car had remair induction kit  , 4 to 1 manifold and a custom 2.5" exhaust . Came in at 206 bh...
22/07/2026

Fn2 in with us for remap . Car had remair induction kit , 4 to 1 manifold and a custom 2.5" exhaust . Came in at 206 bhp leaving us at 212 bhp.

Fn2 in with us for a new air-conditioning condenser,  regas and a map tweak . Came in at 227 bhp leaving us at 239 bhp. ...
22/07/2026

Fn2 in with us for a new air-conditioning condenser, regas and a map tweak . Came in at 227 bhp leaving us at 239 bhp.

Fn2 superchangered in with us for a health check after his charger belt snapped and he felt the car had a few other issu...
19/07/2026

Fn2 superchangered in with us for a health check after his charger belt snapped and he felt the car had a few other issues . ( belt was replaced ) and then ran on the dyno the car made 370 bhp .
We found the coolent , clutch and brake fluid needed changing , rear axle bushes were split and whilst the underside was quiet clean for an fn2 it was time to clean it up and underseal it . (All this work was carried out ).
We looked into an oil leak and found the engine in the car was a k20a2 from the ep3 and had a k20z4 timing chain cover leaving one of the engine mount hole unable to be used coursing a leak . So we fitted a k20a2 timing cover .
We also swapped out the 25mm dv valve from the tts kit to a turbosmart race port 50mm valve , we also checked the fuel pump which had been uprated already from the one in the tts kit .
The custom was unhappy with how heavy and on and off the clutch was . It had a twin plate in so we swap the clutch to a normal single plate to give a more oem clutch feel .
We also removed the custom 3" exhaust with 2.5" back box's and the manifold with a 2.25" collector and swapped it for the piper true 3" full exhaust .
Finally we put the car back on the dyno and mapped it the car is now leaving us with 420 bhp .

Lexus v8 in for and oil and filter service
19/07/2026

Lexus v8 in for and oil and filter service

Address

Unit 3a Veasey Close
Nuneaton
CV116RT

Opening Hours

Monday 8am - 5pm
Tuesday 8am - 5pm
Wednesday 8am - 5pm
Thursday 8am - 5pm
Friday 8am - 5pm
Saturday 9am - 1pm

Alerts

Be the first to know and let us send you an email when Dynodaze Rolling Road £50 Power Runs & Printout posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share