Juuso's Garage

Reittiohjeet

Juuso's Garage Working in the garage. Building all kind of stuff out of metal, wood etc..

New rims and tyres for yhe E39! 9.5x18" with 245/45 tyres all around so I can swap tyres between axles. Had to add 35mm ...
01/07/2026

New rims and tyres for yhe E39!
9.5x18" with 245/45 tyres all around so I can swap tyres between axles. Had to add 35mm spacers to the rear to widen it up, but man they look good!

Small update, 8hp45 from jaguar to fit behind volvo redblock for my BMW E39 time attack car! Flywheel has same bolt patt...
01/07/2026

Small update, 8hp45 from jaguar to fit behind volvo redblock for my BMW E39 time attack car! Flywheel has same bolt pattern to crankshaft so I only need to make spacer between volvo and jaguar flywheel and adapter between transmission and engine

29/03/2026

Got a request for the Volvo Redblock intake manifold to fit 40mm, 45mm, 48mm and 50mm DCOE /DHLA type carburators / ITB's so here are the files. Also modeled the stainless steel sleeves to press into manifold to prevent fl**ge pushed out when clamping down.

50mm intake Step file
https://drive.google.com/file/d/1XXAeAFpSkq8ZkVwCo3FLu-TAIeb62Hiv/view?usp=sharing

50mm intake STL file
https://drive.google.com/file/d/1754q_Iv9qifoKfU_vjqhJjTpjtyDqBdn/view?usp=drive_link

48mm intake STEP file
https://drive.google.com/file/d/1fdNL9uiI9sn7k8npzZPlWMr-1TZLI-66/view?usp=drive_link

48mm intake STL file
https://drive.google.com/file/d/1lJrbPCRz2lrfPhxaWig6RM9xNab6H-Cj/view?usp=drive_link

45mm intake STEP file
https://drive.google.com/file/d/1hwZgoLtgb6BKynsgt3_07XEp20CsLQ4U/view?usp=drive_link

45mm intake STL file
https://drive.google.com/file/d/18ZH0OJw9vI-CRv8eWEKCmCheYu5LWhco/view?usp=drive_link

40mm intake STEP file
https://drive.google.com/file/d/1ZsmgGi68siyh3loVbINIWWkgTd6xGjSl/view?usp=drive_link

40mm intake STL file
https://drive.google.com/file/d/1Cvdwq4E14ONA5cKwnItI96LCYcpLpQ1p/view?usp=drive_link

Blank and m8 threaded sleeves for the intake mounting holes, Step File only.
https://drive.google.com/file/d/1pjacTCBSLDHZsH4lpEHubDMeZcco4MX6/view?usp=drive_link

NOTE!!!
Make the intake sleeves out of stainless steel to prevent rusting and expanding over time. Also adjust the outer diameter of the sleeve with the print hole ID so that the fitment is +/- 0.0mm.

Sleeves should be pushed in with ease, but they should not be falling out. You can add small amount addhesive for example Hylomar if the fitment is too loose

3D printed intake runners are mounted and exhaust manifold is fully welded now!
01/03/2026

3D printed intake runners are mounted and exhaust manifold is fully welded now!

Peugeot is getting some progress 😎
14/01/2026

Peugeot is getting some progress 😎

Turning track e30 for ice racing required a lot of changes, more than we imagined 😅😆 longer control arms with angle kit ...
12/01/2026

Turning track e30 for ice racing required a lot of changes, more than we imagined 😅😆 longer control arms with angle kit and lift kit, e36 hubs, shocks and brakes. Also hydraulic handbrake and welded diff had to be installed

Some exhaust and intake fabricating on the Peugeot. Exhaust will be 4-2-1 type as old one but different design. Intake m...
24/12/2025

Some exhaust and intake fabricating on the Peugeot. Exhaust will be 4-2-1 type as old one but different design. Intake manifold will be longer and with bigger radius on turn. I'll try to 3D print the manifold now, let's see if I can make it

Little progress for a while, it's been a long time since I had a full day in garage 😇Cutting excess sheets metal off, we...
13/12/2025

Little progress for a while, it's been a long time since I had a full day in garage 😇

Cutting excess sheets metal off, welding and grinding. Fitted the rear arches too, that are originally from VW golf.

Osoite

Tampere

Verkkosivusto

Ilmoitukset

Saat tiedon ensimmäisenä: lähetämme sinulle sähköpostia, kun Juuso's Garage julkaisee uutisia ja tarjouksia. Sähköpostiosoitettasi ei käytetä muihin tarkoituksiin, ja voit perua tilauksen milloin tahansa.

Oikopolut

Jaa

Kategoria