Taizhou kingpower rubber belt manufacturing co.,ltd.”

04/07/2016

The belt can be stored for a few years

storage notes :In order to maintain the availability and size of the belt, the power transmission belt must be strictly kept to its proper storage process. Many of the early failure of the belt, can be found in the installation before the storage process is not in accordance with the operation, and the resulting damage to the first. By following the principle of knowing, you can avoid the belt ahead of the failure。

recommend： Belt should be stored in a cool and dry environment without direct sunlight, the ideal storage condition is that the temperature is less than 30 degrees Celsius. Humidity below 70% of the environment.

Forbidden:

No belts are placed near the window to avoid direct sunlight and water vapour.
Prohibit the belt on the heat, radiation and heat source equipment vents
The belt is placed near the transformer and the electric motor to prevent ozone pollution.
No belt is placed in an environment where chemicals are released.
No belt is placed on the floor directly, unless it is protected by a special case.
When installing and storing the winding belt, the bending radius of the belt must be satisfied.

Prohibit the belt tied together, especially the belt bending head prohibited bundled
Prohibit the belt hanging storage, because may cry a very small bending radius, incorrect storage will hurt and causes the belt to belt cord premature failure. Take the belt from the warehouse to get the site installation, also need to pay special attention to avoid the occurrence of the above prohibited matters.

Belt storage:

If the storage temperature is not more than 30 degrees Celsius, the temperature is not greater than 70%, the belt can be stored for 6 years after the use of. In the storage temperature of more than 30 degrees Celsius, the temperature rise of ten degrees Celsius, the belt life will fall by about half.
Belt is prohibited in the temperature of more than 46 degrees Celsius in the environment, otherwise the belt failure time will be greatly ahead of time.
If the humidity is more than 70%, fungi and molds are likely to occur in this environment, which has an impact on the performance of the belt, so try to avoid it.
If the equipment down time for more than 6 months, it should be removed from the belt, the storage environment should also meet the above requirements, the temperature is not more than 30 degrees Celsius, the humidity is not more than 70%

23/06/2016

Failure of multi PK belt and its causes and Countermeasures

* Breakdown of machinery is a very difficult thing. When the machine is in trouble, it is in addition to the new product to find the cause of the fault and the correct method of using it to make full use of the performance and prolong the service life of the machine.

phenomenon reason countermeasure
slippage 1.Tape tension relaxation
2.Overload
3.Contact angle is small
4.With oil or water 1.Give moderate tension
2.To widen the band or to increase the number of bands
3.The idler widening machine with the correct diameter or device
4.Completely remove oil or water. Put on the cover to prevent oil and water from adhering
Early fracture 1.Load change / sudden load is too large
The transmission capacity of the transmission condition is not in accordance with the provisions of the number of hanging machine belt; without the use of the specified belt
2.Increase the heat or increase the use of bending fatigue method (with a wheel diameter is too small, bending angle is too small, too fast speed)
3.Tension becomes loose and slip 1.You can change the design, but the machine belt must be a specified number of bands (according to use, please use a higher level of the machine belt)
2.Take down the heat measure; change the design change the belt wheel diameter, the rotational speed, the bending angle
3.Give moderate tension
Cracking 1.High temperature use
2.Tension becomes loose and slip
3.Continuous emergency stop or emergency start
4.With oil etc.
5.With a wheel diameter is too small, the back of the tension to promote the reverse bending is too strong
6.Direct sunlight 1.Take heat release measures
2.Give moderate tension
3.Change design
4.To avoid the oil and the oil spill
5.Change design
6.Mounted on the belt cover
Ground breaking 1.Tension pulley diameter is too small
2.Bending angle is too small
3.Tension becomes loose and slip
1.Tension band wheel with larger diameter
2.Relax bending width
3.Give moderate tension

abrasion 1.Rust or belt wheel groove surface roughness
2.Tension pulley diameter is too small
3.The angle of the belt wheel is not correct; the shape of the belt wheel is abnormal, and the angle of the belt wheel groove is not accurate. 1.Processing of the belt wheel groove
2.Tension band wheel with larger diameter
3.The dislocation is less than 1/3, and the belt pulley is changed.

23/06/2016

The belt can be stored for a few years

storage notes :In order to maintain the availability and size of the belt, the power transmission belt must be strictly kept to its proper storage process. Many of the early failure of the belt, can be found in the installation before the storage process is not in accordance with the operation, and the resulting damage to the first. By following the principle of knowing, you can avoid the belt ahead of the failure。

recommend： Belt should be stored in a cool and dry environment without direct sunlight, the ideal storage condition is that the temperature is less than 30 degrees Celsius. Humidity below 70% of the environment.

Forbidden:

No belts are placed near the window to avoid direct sunlight and water vapour.
Prohibit the belt on the heat, radiation and heat source equipment vents
The belt is placed near the transformer and the electric motor to prevent ozone pollution.
No belt is placed in an environment where chemicals are released.
No belt is placed on the floor directly, unless it is protected by a special case.
When installing and storing the winding belt, the bending radius of the belt must be satisfied.

Prohibit the belt tied together, especially the belt bending head prohibited bundled
Prohibit the belt hanging storage, because may cry a very small bending radius, incorrect storage will hurt and causes the belt to belt cord premature failure. Take the belt from the warehouse to get the site installation, also need to pay special attention to avoid the occurrence of the above prohibited matters.

Belt storage:

If the storage temperature is not more than 30 degrees Celsius, the temperature is not greater than 70%, the belt can be stored for 6 years after the use of. In the storage temperature of more than 30 degrees Celsius, the temperature rise of ten degrees Celsius, the belt life will fall by about half.
Belt is prohibited in the temperature of more than 46 degrees Celsius in the environment, otherwise the belt failure time will be greatly ahead of time.
If the humidity is more than 70%, fungi and molds are likely to occur in this environment, which has an impact on the performance of the belt, so try to avoid it.
If the equipment down time for more than 6 months, it should be removed from the belt, the storage environment should also meet the above requirements, the temperature is not more than 30 degrees Celsius, the humidity is not more than 70%.

TAIZHOU KINGPOWER RUBBER BELT MANUFACTURING CO.,LTD
SANMEN FUWEI RUBBER BELT MANUFACTURING CO.,LTD
ADD:Xiahu Development Zone,Zhuao,Sanmen,Zhejiang ,China
Tel: 0086-576-83111161/83111881
Fax:0086-576-83112338/83110491
Web Site: www.kingpowerbelt.com

22/04/2016

view of company machines

11/04/2016