Shape & Shine

Directions

Shape & Shine Custom Body & Paint studio, specialising in:
- Award Winning Body & Paint
- Automotive Fabrication
- Metal Shaping
- By Appointment Only -

After letting the polyester cure for the required time, I started splining down the polyester to head toward the paint s...
07/10/2026

After letting the polyester cure for the required time, I started splining down the polyester to head toward the paint stage. Coming up really nice and sharp. Spending the time on the metal and the early bodywork stages really saves time, headache and gives proven results when you approach the end of the bodywork stages.

With the body shell and all hanging panels in RestoFinish epoxy, we fit the panels up and gapped them up ready for bodyw...
30/09/2026

With the body shell and all hanging panels in RestoFinish epoxy, we fit the panels up and gapped them up ready for bodywork. Outside for a bit of a sun bake.

Next it was time for a good clean, a good scrub with deoxidine, then in to the booth for some RestoFinish epoxy. I alway...
28/09/2026

Next it was time for a good clean, a good scrub with deoxidine, then in to the booth for some RestoFinish epoxy. I always spend a lot of time on this stage to make sure the metal is spotless. Gloves are warn at all times while cleaning and masking, so the metal isn't touched, to eliminate the chance of any contaminants.

Next up on the VL, the task was to fix the boot lid to parcel tray panel gap, which is a common issue on VL & VK. After ...
25/09/2026

Next up on the VL, the task was to fix the boot lid to parcel tray panel gap, which is a common issue on VL & VK. After completing that, we trial fit all the panels to see where we were at with gaps and panel alignment.

After spending some time tapping and trying to convince the metal to go where I wanted it to go, I can say I'm happy wit...
23/09/2026

After spending some time tapping and trying to convince the metal to go where I wanted it to go, I can say I'm happy with the result. By no means is it file finished, however, with minimal access due to the car being tubbed and the inner fuel filler area not being cut out, I did what I could with the time and budget I was given. The car requiring much less filler is always a good thing. Foundations are much more important than the finished product. I also tapped up the drivers side front and rear door. Getting closer to epoxy now.

The drivers side quarter panel had the fuel filler welded at some point in the past, and was pretty badly heat affected....
21/09/2026

The drivers side quarter panel had the fuel filler welded at some point in the past, and was pretty badly heat affected. So I got the hammers and dollies out, and started tapping. Pretty happy with how it came out.

After inspecting all the panels on the VL, we got started tapping up any lows. By no means is this a file finished job, ...
28/08/2026

After inspecting all the panels on the VL, we got started tapping up any lows. By no means is this a file finished job, however, the car will require much less filler and bodywork materials, which will provide a higher quality and longer lasting finish. What's underneath the paint needs to be right before progressing to the next stage of the bodywork process.

We started removing the epoxy to inspect the condition of the roof skin. It wasn't great, a lot of highs and lows to add...
26/08/2026

We started removing the epoxy to inspect the condition of the roof skin. It wasn't great, a lot of highs and lows to address.

Upon inspection, the VL needed a fair bit of repair work.
21/08/2026

Upon inspection, the VL needed a fair bit of repair work.

We've had a VL Group A come in for body and paint. Looking forward to getting stuck into this one.
19/08/2026

We've had a VL Group A come in for body and paint. Looking forward to getting stuck into this one.

Address

Sydney, NSW

Opening Hours

Monday 9am - 5pm
Tuesday 9am - 5pm
Wednesday 9am - 5pm
Thursday 9am - 5pm
Friday 9am - 5pm
Saturday 9am - 5pm

Website

Alerts

Be the first to know and let us send you an email when Shape & Shine posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share