DC Motorsport

06/09/2026

🏆 FRANK’S DATTO HAS DONE IT AGAIN! 🏆

Frank Cannistra’s Datto just keeps getting it done! 🔥

This time, taking out FASTEST RWD at the Turbosmart Flying 500! 🏁💨

A massive result for Frank and everyone involved in keeping this thing at the pointy end. 💪

Huge thanks to Rigoli Performance for the engine, maintenance and keeping the car on song, and Murphs Performance & Mechanical for getting the power to the ground and making this thing pick the front wheel up! 👊

Haltech for making our lives just that bit easier

Another trophy for the cabinet! 🏆

DC Motorsport 🔧🏁weekend

31/08/2026

29/08/2026

26/08/2026

🏆 ROLL RACING SYDNEY 2WD NIGHT WINNERS — FOR THE 4TH TIME! 🏆

What a weapon Frank Cannistra's Datsun has become! 💪

This car is absolutely flying, but more importantly, it’s consistent — and consistency is everything at an event like Roll Racing.

A massive thanks to Murphs Performance & Mechanical Suspension. The work they’ve put into the suspension setup has made a huge difference in getting this car down consistently, pass after pass.

And a huge thanks to Rigoli Performance for keeping the car on point — maintenance, engine work and everything else this thing needs to keep performing at this level.

Four-time Roll Racing Sydney 2WD Night winners! 🏆🏆🏆🏆

Awesome result, boys. Thanks for everything! 🤝🔥

08/08/2026

We recently had this epic XY Falcon in the workshop for a fresh tune.

Packing a Warspeed LS topped with a 6/71 blower, this thing has all the right ingredients for an old-school tyre killer.

After giving everything a thorough check-over, we got to work dialling in the Haltech ECU to get the most out of the combination.

The result?

An absolute mountain of torque that's ready to annihilate tyres at the slightest touch of the throttle. 🔥💨

This is exactly what blown V8s are all about!

07/08/2026

We recently had this epic Ford Ranger in the workshop for a tune-up.

But don't let the body fool you... This is no ordinary Ranger.

Under the bonnet is a built LSA, controlled by a Link ECU, making this one seriously wild drift truck.

After a thorough inspection, we strapped it to the hub dyno and got to work refining the calibration.

The result? Over 700 RWHP and a tune that's ready to party.

This is definitely one to keep an eye on at the next drift event. 🔥💨

06/08/2026

We recently had this mint VZ Calais in the workshop after the new owner wasn't happy with the way it drove.

After giving the car a thorough health check, we got to work recalibrating the factory ECU using HP Tuners to unlock its full potential while dramatically improving the drivability.

The end result?

430 RWHP and a car that's not only quicker but far smoother and more enjoyable to drive every day.

Power is one thing... but a car that drives as good as it performs is what we're really aiming for. 👌

05/08/2026

Kevvi's mint FG F6 made the trip all the way down from the Gold Coast for a few upgrades and a fresh tune.

We fitted a new intake, an AES valve, and an onboard air system for CO₂ boost control before strapping it to the hub dyno.

The car had previously made around 1000 RWHP at 40psi, so we dialled the CO₂ boost control back to the same 40psi and got to work.

The graph says it all. Both runs are at the exact same boost pressure. The only difference? Properly tuning the VCT (Variable Cam Timing).

This is why camshaft tuning is so important on these engines. There was a huge amount of torque left on the table, and with the VCT dialled in, the improvement speaks for itself.

To finish it off, we set up Haltech Traction Control... for those "Mexico" races. 😉🇲🇽

04/08/2026

Pat's immaculate VX was back on the dyno recently after a few upgrades.

The old 4L60E had reached its limits, so we replaced it with a tough Shift right 4L80E built to handle the extra power.

Controlled by the Haltech TI4L, this Sunday cruiser is anything but tame, laying down 700+ horsepower at the hubs. 👊🔥

Looks stock. Drives like a cruiser. Hits like a freight train.