Custom Garage

Custom Garage Custom Garage is your one stop performance shop from brake upgrades to turn key restorations

A little repair work on the firewall while we wait for the new front to return from the media blasters . The very commo...
02/03/2022

A little repair work on the firewall while we wait for the new front to return from the media blasters . The very common bash the hell out of the firewall mod to give the clutch fork clearance . Same was done for starter motor clearance . I have never had clearance issues with the rx2 - rx3 - rx4 the only ones we use to modify with a fabricated recess was the 1000 utes - r100 - 1300 etc .

Onto the chassis bench and off with the front. Drivers side rail was 20mm higher than the passenger side rail 🤔. Usual...
01/03/2022

Onto the chassis bench and off with the front. Drivers side rail was 20mm higher than the passenger side rail 🤔. Usually we can undrill the spot welds and slide the front off but someone had previously seam welded ( quality welds 🥴) a new front on which means we had to cut the bulk of and then unpick the rest of the firewall one piece at a time . A mix of mig and braze weld on this one .

Another mazda rx2 coupe we are bringing back from the dead . From what we can see it has had a full front replacement an...
28/02/2022

Another mazda rx2 coupe we are bringing back from the dead . From what we can see it has had a full front replacement and then another half front replacement in its life . From the damage on both quarters and rear valance and front swaps im guessing it was a rally car once in its life . More pics to follow 👍

Just a heads up for people buying these repro mazda Rx3 arm rests that everyone is selling . We had a customer supply so...
19/11/2021

Just a heads up for people buying these repro mazda Rx3 arm rests that everyone is selling .
We had a customer supply some to fit to his rx3 sedan thinking they were like the factory ones fitted .
As you can tell from the pics they look nothing like rx3 arm rests plus they are gray and not black . We also had to die grind out the holes so a decent sized washer could be fitted so they wont pull of the door . Bolt spacing is also approx 5mm out from the factory ones but the holes are big enough to allow you to bolt them in off centre . Yes they do fit on but no they are not repro rx3 they are infact mazda b2000 - 2200 - 2600 ute arm rests .

Mazda Rx4 engine bay looms in today for an update
03/09/2021

Mazda Rx4 engine bay looms in today for an update

Before and after on the rx3 RH loom. Stripped . Circuits not required removed . New braided covering and new plugs inst...
02/09/2021

Before and after on the rx3 RH loom. Stripped . Circuits not required removed . New braided covering and new plugs installed. Now setup as plug n play. Includes a new fuse/relay box and circuit breaker ( not pictured )

Before and after on the rx3 LH loom. Stripped . Circuits not required removed . New braided covering and new plugs inst...
02/09/2021

Before and after on the rx3 LH loom. Stripped . Circuits not required removed . New braided covering and new plugs installed. Now setup as plug n play

Wiring fun. Rx3 this time. Complete strip down with this one . Upgrade some of the circuits . Remove what isn't needed a...
24/08/2021

Wiring fun. Rx3 this time. Complete strip down with this one . Upgrade some of the circuits . Remove what isn't needed and convert it from left hand drive to right had drive. Which means the terminal removal tools are going to get a workout 🥴

I think this person found out it doesn't matter how much brush on body sealer you use it still won't straighten that be...
11/03/2020

I think this person found out it doesn't matter how much brush on body sealer you use it still won't straighten that bent chassis rail 🥴. We get all the good jobs 😭

Finally found some solid metal 🎊🎉. Now to clean it all up and start fabricating replacement sections. .All internal pane...
21/02/2020

Finally found some solid metal 🎊🎉. Now to clean it all up and start fabricating replacement sections. .All internal panels will be treated and sealed while it is all open .

Fixing other people's repairs and finding more rust . All in a day's work when your playing with old Mazda's . Rx4 sedan...
21/02/2020

Fixing other people's repairs and finding more rust . All in a day's work when your playing with old Mazda's . Rx4 sedan today

Some custom injection setups we built before Xmas for some lucky customers. One set for a Datsun 260z and the other for ...
17/01/2020

Some custom injection setups we built before Xmas for some lucky customers. One set for a Datsun 260z and the other for a Cortina . Kits start from $1650 . We can also supply with plug and play looms and ecus .

Address

Www. Customgarage. Com. Au
Adelaide, SA
5000

Opening Hours

Monday 9am - 5pm
Tuesday 9am - 5pm
Wednesday 9am - 5pm
Thursday 9am - 5pm
Friday 9am - 5pm

Telephone

+61410546004

Website

Alerts

Be the first to know and let us send you an email when Custom Garage posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category