Moparts BoneYard

Moparts BoneYard The exclusive source for authentic original Mopar equipment parts and accessories �

I would like to sell locally but will ship. Located in Green Bay Wi Parting out 340 engine, I am keeping the block and g...
09/10/2025

I would like to sell locally but will ship. Located in Green Bay Wi

Parting out 340 engine, I am keeping the block and going with a stroker setup. Bought it used and found the pistons were installed incorrectly and the valves hit the pistons. I was told that it was rebuilt and run a very short time in the car. Machine shop looked at the internals and said the pistons, rods, lifters, rockers, rods, cam, oil pump, wind age tray, can be re-used.

Block is not for sale. I included pictures to show how clean the cylinders were after disassembly.

Pistons: .030 TRW

Crank: not available at the moment, being inspected for damage.

Heads: being magnafluxed this week, will see if the valves are ok or not. I will sell separately for $450 if they check out good.

Cam: I don’t know the cam specs.

Oil pan is straight and clean. Intake is an Edelbrock Torker 340.

Would prefer to sell the entire lot minus the heads for $750 but will sell parts separately if there is no interest in the lot.

Torque Thrust Wheels and Cooper Cobra Tires.!Torque Thrust D wheels 15x7 (front) and 15x8 (rear). Comes as a package. Ti...
09/10/2025

Torque Thrust Wheels and Cooper Cobra Tires.!

Torque Thrust D wheels 15x7 (front) and 15x8 (rear). Comes as a package. Tires are Cooper Cobra 235/60-15 and 275/60-15. Asking $550, tires are brand new, barely used. Fits a 5x4.5 bolt pattern.

I have a gear vendors overdrive for 727 transmission, it was installed in a Dodge Charger ,but will fit any chassis.
Project I bought that was never finished.
Even though it was connected to the transmission and installed in the car it's never been Used I have all paperwork, module, wiring etc.
I also have drive shaft for B body.
Located in Green bay Wisconsin $1500.00 Take it

Real 340 sw***er new AMD full quarters newAMD fenders and hood, new inserts and 340 call outs, stainless steel exhaust w...
09/08/2025

Real 340 sw***er new AMD full quarters new
AMD fenders and hood, new inserts and 340 call outs, stainless steel exhaust with flowmasters and x pipe, 340 with aluminum heads h beam rods diamond pistons lunati voodoo cam runs strong 727 reverse manual 3800 t/a converter new in box, alloy big bolt pattern axles new in box, big bolt pattern front disc brakes with spindles rotors calibers and tubular uppers new aluminum drive shaft with over size u joints 8-3/4 rear with 489 case and 4.10s and also a spare 489 case with 4.10s all interiors there and redone except headliner and carpet new tail light buckets lenses and bezels new headlight bezele new inner/outter door handles 2 really nice grills.

Located in Green Bay Wisconsin

Large collection of mopar 4 speeds and rear end center sections gear sets and related parts like to sell as lot.there’s ...
09/08/2025

Large collection of mopar 4 speeds and rear end center sections gear sets and related parts like to sell as lot.there’s much more than what’s in the photos. Plus I have 66-70 new AMD floor pans in stock, pick up for $650. This 3-piece set runs $740 plus 2-300 shipping online. I also have original set of floors 66-70,and 71-2 B body. 68-70 B body one or 2 piece trunk floor in stock. Can offer discounts on all AMD, Legendary Interiors, QA1, Classic Industries orders. Also offer professional Mopar sheet metal installation, and restoration services, and hard to find parts.

Set of Mopar Stage 6 heads set up for .750 lift solid roller. Done by Compuflow back in the day. 70 passes since last fr...
09/07/2025

Set of Mopar Stage 6 heads set up for .750 lift solid roller. Done by Compuflow back in the day. 70 passes since last freshen. 2.25 intake, 1.84 exhaust. Comes with nearly new set of Harland Sharp 1.5 rockers, RB spacers, Mopar M1 manifold, valley pan cover, hold downs, pushrods and ARP studs and nuts. Went to max wedge ports only reason for selling. $2,500, could ship at your dime

Silver Sport Mopar Big Block transmission kit fits 67-76 A-body, 66-74 B-Body and 70-74 E-Body. I purchased this kit for...
09/06/2025

Silver Sport Mopar Big Block transmission kit fits 67-76 A-body, 66-74 B-Body and 70-74 E-Body. I purchased this kit for my 68 Plymouth GTX and it installed and fit well. I never finished installing the transmission kit in the GTX when my wife passed in 2017 and turned my life upside down. During my devastating loss my plans changed for our GTX and I’m now moving in a different direction and selling the GTX. The transmission kit is in new condition and is ready to install in a car. The transmission kit includes the transmission mount, driveshaft and related components. It does not include a starter however a high torque aftermarket Mopar starter is recommended. I paid over $5700 for this kit and will sell the kit for $2800. A great deal for someone who wants to put an overdrive transmission behind their big block Mopar engine.

Selling a pair of black buckets seats from a 71 C Body. Seats are complete with power seat tracks. Passenger seat lays b...
09/05/2025

Selling a pair of black buckets seats from a 71 C Body. Seats are complete with power seat tracks. Passenger seat lays back manually. Very good condition. Seats are located in Green Bay Wi. $350 or best offer

I acquired these seats a over 20 years ago for a project that never panned out. These seats are in great condition but do have a couple tiny cracks as seen in the pics. They have been garage kept and wrapped in plastic. I believe one seat is missing a track so that will need to be replaced. I'm asking $600 OBO . I don't mind shipping but it will be at buyers expense.

010. eagle h beam rods installed. I have the original rods too. Bottom end balanced. The engine has low hours, but due t...
09/04/2025

010. eagle h beam rods installed. I have the original rods too. Bottom end balanced. The engine has low hours, but due to sitting years between being started the cylinders got moisture. And a cam lobe started to wear. Not sure if the torque plate honed .020 bores will clean up or need to bored .030? Two cylinders? The block is clean no sleeves or stripped threads.
The T/A heads do not appear to have had machine work done and have been magnafluxed. I have all the valves and springs but missing the keepers. The T/A rockers and shafts are in good shape. I also have the original push rods.

I am asking $5000 OBO

T/A 340 long block for sale. Short block was rebuilt in 2001. T/A heads set aside and stored. Rebuilt standard J heads. The engine was bored .020, crank ground .010,

Located in Green Bay Wisconsin

This is a meticulously restored carburetor setup, built from the ground up with new and excellent original parts. The ma...
09/03/2025

This is a meticulously restored carburetor setup, built from the ground up with new and excellent original parts. The manifold is brand new, and the carburetors have been freshly rebuilt. All components are either new or carefully sourced from excellent original stock. Delivered with sticker of your choice (of course).
As shown in the pictures, this is an exceptionally nice and highly complete assembly.located in portland maine
The setup includes:
- New manifold
- Freshly rebuilt carburetors (3577185)
- New/excellent original parts: fuel lines, linkage, hardware, coil bracket, throttle cable bracket, return springs, idle solenoid, choke spring, vacuum lines
- New gaskets (OEM), air filter, Dodge/Plymouth decal
- New Fel-Pro intake gaskets, manifold bolts
$1500.00
OBO
Fits:
Dodge:
- Charger (1969-1971)
- Coronet (1969-1971)
- Dart (1969-1971)
- Super Bee (1969-1971)
Plymouth:
- Road Runner (1969-1971)
- Satellite (1969-1971)
- GTX (1969-1971)
- Sport Satellite (1969-1971)
Mopar or no car!

74 440HP that was rebuilt once 30 years ago butunknown miles. It has the 906 HP early cylinderheads.$950.0072 H440HP tha...
09/02/2025

74 440HP that was rebuilt once 30 years ago but
unknown miles. It has the 906 HP early cylinder
heads.
$950.00

72 H440HP that is pretty complete. Dented Oil pan but
I have lots of spares.
$950.00

Both these I am selling as core engines but if there is
any issue with the crankshafts/Blocks/Heads = I will replace them
as I have a dozen more of all them.

These are real HP engines with steel cranks and all the
HP stuff!

ALSO: A bare block 72 H440 HP empty block

ALSO: Another Dozen 383 and 440 empty block that I do not
much about and have not inspected yet:

$225 for 383s and $300 for44s0 if not stamped HP, $375 if stamped HP, although there is absolutely no difference in the blocks.

NOTE: Pickup and Shipping available

THE PRODUCT IS A 440 MOPAR ENGINE FROM 1970’S WITH MACHINE WORK DONE AND NEW AND RECONDITIONED PARTS. IT IS DESIGNED FOR...
08/31/2025

THE PRODUCT IS A 440 MOPAR ENGINE FROM 1970’S WITH MACHINE WORK DONE AND NEW AND RECONDITIONED PARTS. IT IS DESIGNED FOR VEHICLES SUCH AS CHARGER, ROADRUNNER, CUDA, CHALLENGER, GTX, DEMON, AND SW***ER. THIS VINTAGE PART IS A PERFORMANCE ENGINE WITH 8 CYLINDERS AND A SIZE OF 440. THE ENGINE HAS BEEN REBUILT WITH NEW AND RECONDITIONED PARTS, MAKING IT READY TO BUILD FOR A CLASSIC VEHICLE.

THIS 440 HAS MOST MACHINE WORK DONE AND PRETTY MUCH READY TO ASSEMBLE. NEW PISTONS WITH RECONDITIONED RODS, CRANKSHAFT FRESHLY DONE, BLOCK IS BORED AND MACHINED FOR ASSEMBLY, HEADS ARE FRESH WITH NEW STAINLESS VALVES, NEW GASKETS, NEW BEARINGS, NEW TIMING CHAIN, NEW OIL PUMP, RESTORED OIL PAN AND THE LIST GOES ON. SEE PICTURES. NO INTAKE OR CAMSHAFT SO YOU CAN PICK WHAT YOU WANT. THE SHORT BLOCK IS 1970'S AND THE HEADS ARE 1967 915 CLOSED CHAMBER WHICH WILL GIVE YOU ABOUT 1 POINT MORE COMPRESSION. THAT'S ABOUT 15 EXTRA HORSE POWER.

SHIPPING ON PALLET IN CONTINENTAL U.S TO A BUSINESS OR TERMINAL. RESIDENTIAL DELIVERY AVAILABLE BUT MIGHT COST MORE. CONTACT ME FOR SHIPPING PRICE.

New never run 440 six pack set up. Edelbrock aluminum intake (powder coated hemi orange), 3 new holley six pack carbs (2...
08/28/2025

New never run 440 six pack set up. Edelbrock aluminum intake (powder coated hemi orange), 3 new holley six pack carbs (2x 4365, 1x 4144), new linkage, new fuel line set. This set is ready to bolt on and run. $2500/BO + shipping from Green Bay Wi . Message Or Call me for more info

I have a gear vendors overdrive for 727 transmission, it was installed in a Dodge Charger, but will fit any chassis.
Project I bought that was never finished.
Even though it was connected to the transmission and installed in the car it's never been Used I have all paperwork, module, wiring etc.
I also have drive shaft for B body.
Price $1500 Take it

Set of 15x7 JJ OEM Rallye Wheels 2944390 (Five), Aftermarket Rings (Five), and Center
Caps (Four)
Tires and Wheels are basically brand new!
Less Than
20 Miles on them. Wheels come with Center Caps! $550 OBO For All!

[email protected]

I’ll take $3,800 shipping included for them all.

Address

Green Bay, WI

Telephone

+18597404559

Website

Alerts

Be the first to know and let us send you an email when Moparts BoneYard posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Moparts BoneYard:

Shortcuts

Featured

Share

Category